Shopping Cart
There are no more items in your cart
Futaba 6L, receiver R3106GF (mode 1)
FUT5003116
Six-channel RC set Futaba T-FHSS Air-2.4GHz (without telemetry) for recreational models of airplanes, cars and boats. Cross controls, 1 switch, 1 rotary control for channels 5 and 6, yaw direction switches, switchable mixers for ailerons, butterfly tail surfac
Express delivery
Large selection of carriers
Satisfaction guarantee
Futaba 6-channel classic RC set using T-FHSS Air-2.4GHz telemetry transmission system for recreational modelers who like everything under direct manual control. With the R3106SB receiver included in the kit, you have 6 PWM channels for classic servos.
Perfectly fitting in the hand, the T6L Sport transmitter features cross-controls with selectable arrest / neutralization, 1 switch, 1 rotary proportional control, 4 mechanical trim. The T6L is also equipped with a teacher-student drawer. There are deflection switches for all channels and switchable mixes for auto-wings, butterfly tails and flaperons.
To operate the transmitter, you will need 4 AA alkaline batteries or NiMH batteries stored in the transmitter holder.
FUNCTION
- T-FHSS Air-2.4GHz transmission system without telemetry
- 6 proportional channels
- Cross Controls (Transmitters available in Mode 1 or 2, subject to change)
- Rotary proportional control for channel 6
- Two-position switch for channel 5
- 4 mechanical trim
- Deflection sense switches for channels 1-6
- Teacher-pupil socket (the transmitter can only be used as a pupil or for controlling a PC simulator)
- Mix elevons (for flying wings).
- Mix of butterfly tail
- Mix flaperons (to control the ailerons of 2 servos simultaneously operated as flaps / aerodynamic brakes with channel 6 knob)
RC SET CONTAINS
- Transmitter Futaba T6L Sport 2.4GHz in mode 1
- R3106SB Receiver
- Operating Instructions
CA-RVIN-700 cable for measuring external voltage (eg drive battery) in the range 0 - 70V. Only for compatible telemetry receivers with special port (R3008SB, R7008SB, R7014SB, R7108SB).
Teacher-student cable with a "square" connector at both ends.
Telemetry current sensor. Measurement in the range: voltage 0 - 70V, current 0 - 150A, elapsed electric charge (max. 32 767mAh). Connection to S.BUS2 bus. Total length of power cable including sensor
Last items in stock
Speed sensor of internal combustion engines OS Engines. Connection to governor (GV-1), gyro (GY701) or FBL Futaba unit (CGY760R / CGY755). The sensor is directly designed for mounting in the rear cove
Telemetric GPS sensor for measuring distance and speed with built-in barometric altimeter / vario. Measurement in the range: speed 0 - 500km / h, height -700 to + 5500m, vario -150 to + 150m / s. Conn
Miniature super light receiver Futaba T-FHSS Air-2.4GHz for indoor models and park-flyers. Power supply 3.2-8.4 V, dimensions 20.0x10.0x3.0 mm, weight 1.0 g. Soldering terminals for servos, wide supply voltage range (also for 1S LiPo). Limited range of...
Last items in stock
S-BUS decoder enabling the connection of up to three classic servos to the S-BUS with cables with a total length of 110 cm. Suitable for analog and digital servos with a standard power supply of 4.8-6.0 V (4-5 cells NiMH). Cannot be used for S-BUS2.
Last items in stock
S-BUS decoder enabling the connection of up to three classic servos to the S-BUS with cables with a total length of 160 cm. Suitable for analog and digital servos with a standard power supply of 4.8-6.0 V (4-5 cells NiMH). Cannot be used for S-BUS2.
S-BUS decoder enabling the connection of up to three classic servos to the S-BUS with cables with a total length of 20 cm. Suitable for analog and digital servos with a standard power supply of 4.8-6.0 V (4-5 cells NiMH). Cannot be used for S-BUS2.
S-BUS decoder enabling the connection of up to three classic servos to the S-BUS with cables with a total length of 140 cm. Suitable for analog and digital servos with a standard power supply of 4.8-6.0 V (4-5 cells NiMH). Cannot be used for S-BUS2.
Last items in stock
S-BUS decoder enabling the connection of up to three classic servos to the S-BUS with cables with a total length of 60 cm. Suitable for analog and digital servos with a standard power supply of 4.8-6.0 V (4-5 cells NiMH). Cannot be used for S-BUS2.
S.BUS / S.BUS2 splitter / extension cable 100 cm with 3 sockets for S.BUS / S.BUS2 devices. Three-core cable with power cable (with orange servo connector) - enables power supply of S-BUS / S.BUS2
S.BUS / S.BUS2 splitter / extension cable 100 cm with 3 sockets for S.BUS / S.BUS2 devices. Two-core cable without power supply cable (with green servo connector) - enables power supply of S-BUS / S.B
S.BUS / S.BUS2 splitter / extension cable 10 cm with 3 sockets for S.BUS / S.BUS2 devices. Three-core cable with power supply cable (with orange servo connector) - enables power supply of S-BUS / S.BUS2 devices from the receiver.
Last items in stock
S.BUS / S.BUS2 splitter / extension cable 10 cm with 3 sockets for S.BUS / S.BUS2 devices. Two-core cable without power supply cable (with green servo connector) - enables power supply of S-BUS / S.BU
S.BUS / S.BUS2 splitter / extension cable 150 cm with 3 sockets for S.BUS / S.BUS2 devices. Three-core cable with power cable (with orange servo connector) - enables power supply of S-BUS / S.BUS2
S.BUS/S.BUS2 splitter/extension cable 150 cm with 3 sockets for S.BUS/S.BUS2 devices. Two-core cable without power supply wire (with green servo connector) - enables power supply of S-BUS/S.BUS2 devices from a special battery connected to one of the...
- New
S.BUS / S.BUS2 splitter / extension cable 30 cm with 3 sockets for S.BUS / S.BUS2 devices. Three-core cable with power cable (with orange servo connector) - enables power supply of S-BUS / S.BUS2 devi
S.BUS / S.BUS2 splitter / extension cable 30 cm with 3 sockets for S.BUS / S.BUS2 devices. Two-core cable without power supply cable (with green servo connector) - enables power supply of S-BUS / S.BU
S.BUS / S.BUS2 splitter / extension cable 50 cm with 3 sockets for S.BUS / S.BUS2 devices. Three-core cable with power cable (with orange servo connector) - enables power supply of S-BUS / S.BUS2 devi
S.BUS / S.BUS2 splitter / extension cable 50 cm with 3 sockets for S.BUS / S.BUS2 devices. Two-core cable without power supply cable (with green servo connector) - enables power supply of S-BUS / S.BU
70 mm Y-cable for S.BUS / S.BUS2 servos.
Telemetric barometric sensor for height measurement/variometer, measurement in the range: relative height -700 to +5500m and vario -150m/s to +150m/s. Connection to the S.BUS2 bus. Total length 175mm, weight 2.6g. Power supply 3.7-7.4V.
Telemetry sensor S.BUS2 for measuring the position of the servo lever, current (up to 10A) and temperature (-10 to 115 ° C) of two S.BUS2 servos. Connection to S.BUS2 bus. Total length 300mm, weight 9
Last items in stock
Telemetric magnetic speed sensor, measuring in the range 360 - 100,000 rpm. Connection to S.BUS2 bus. Total length 255mm, weight 4.7g. Power supply 3.7-7.4V.
Telemetric optical speed sensor, measurement in the range 360 - 300,000 rpm. Connection to S.BUS2 bus. Total length 160mm, weight 4.9g. Power supply 3.7-7.4V.
Telemetric phase speed sensor for AC motors (BLS), measurement in the range 360 - 300 000. Connection to S.BUS2 bus. Total length 475mm, weight 3.8g. Power supply 3.7-7.4V. The sensor connects to
S.BUS/S.BUS2 terminal (hub) with 6 sockets for connecting S.BUS/S.BUS2 devices. The S.BUS output of the receiver and the S.BUS servo can be plugged into any socket. The hub is equipped with feet for easy installation in the model using screws.
Telemetric temperature sensor for measurements in the range of -20 to +200°C. Connection to the S.BUS2 bus. Total length 535mm, weight 4.7g. Power supply 3.7-7.4V. Ideal for measuring the temperature of internal combustion engine heads and similar...
Telemetric temperature sensor for measurements in the range of 0 to 125°C. Connection to the S.BUS2 bus. Total length 350mm, weight 3.8g. Power supply 3.7-7.4V. Ideal, for example, for measuring the temperature of electric motors (especially AC) and...
Central strap with carabiner for comfortable hanging of Futaba transmitters - in black.
Central strap with carabiner for comfortable hanging of Futaba transmitters - in orange.
Last items in stock
Telemetry sensor for measuring the drive battery voltage in the range 0-100V. Connection to S.BUS2 bus. Total length 870mm, weight 6g. Power supply 3.5-8.4V.
- Special price
AA (pencil) NiMH batteries with very low self-discharge suitable for powering receivers in RC models and similar applications with lower current consumption, but the required long life. Weight: 26g, dimensions: 14.5x50.4mm, voltage: 1.2V
AA (pencil) NiMH batteries with very low self-discharge suitable for powering receivers in RC models and similar applications with lower current consumption, but required long endurance. Weight: 28.4 g, dimensions: 14.5x50.4 mm, voltage: 1.2 V, max....
Practically finished model of a motorized glider made of almost indestructible extruded expanded polyolefin (EPO) with an AC motor. Controlled rudder, elevator, ailerons. Equipped with AC motor, controller and 4 servos.
Practically finished model of a motorized glider made of almost indestructible extruded expanded polyolefin (EPO) with an AC motor. Controlled rudder, elevator, ailerons. Equipped with AC motor, controller and 4 servos.
Customers who bought this product also bought:
APC propellers are injected from composite materials using long glass or carbon fibers with a nylon matrix.
Combo set of AC electric motor with rotary casing with 20A controller for aircraft models: glider 450g, trainer 450g, acro 400g, 3D 300g, KV1400 rpm on V, Lixx 2-3s power supply, shaft 3.175 mm.
- Special price
AA (pencil) NiMH batteries with very low self-discharge suitable for powering receivers in RC models and similar applications with lower current consumption, but the required long life. Weight: 26g, dimensions: 14.5x50.4mm, voltage: 1.2V
Microprocessor quick charger with balancer for 1-15 cells NiCd / NiMH, 1-6 cells LiPo / Li-ion / LiFe, LiHV, 2-20V Pb with current 0.1-6A (max. 80W). Discharge max. 2A (max. 10W). Power supply 11-18V / 230V 50Hz. Internal resistance measurement,...
Tap to zoom
