Hangar 9 Ultra Stick 50e PNP

Plug-N-Play®, Plug and Fly

The PNP version makes it much easier to complete the model. The Ultra Stick has a power unit and rudder servos installed. In addition, a propeller with a cone is included, so you can prepare your RC kit and drive battery. You do not glue anything, only screws are used for assembly.

Thoughtful design

It is not a rule that a simple model has to look a dozen. This is evidenced by the construction and color, which are in design harmony and as a whole look pleasant. The practical solution of the model is dominated by the landing gear, which tolerates even larger errors of the pilot during landing / p>

Proven lightweight construction

The model is made of solid light balsa and plywood, precise laser-cut parts form a rigid structure. The original coating of Hangar 9® UltraCote® with finished color is durable and has a color-differentiated top and bottom of the sash.

Easy installation

No glue is needed for installation and you can have the Ultra Stick PNP ready to fly in less time than it needs to charge the battery! Thanks to the design of the wing, transport and storage is practical and convenient.

Wide flight envelope

The low surface load of the wing and the practical design in combination with the large control surfaces, which can be adjusted by means of double deflections, make the Ultra Stick the ideal aircraft for developing your piloting skills. The double aileron flaps allow adjustment in the function of double ailerons or as separate flaps or by using a transmitter mix to couple the flaps with the elevator. combinations, there are no limits.

Smart technology

The Ultra Stick PNP is equipped with the exclusive SMART Spektrum ™ Avian regulátor controller, which can provide a range of telemetry data related to the real-time power system, including motor speed, current, battery voltage and more via compatible Spektrum receivers and transmitters equipped with Spektrum AirWare ™.

Optional accessories

Do you want to fly on water? Add optional EFLA5600 floats and the EFLA5605 kit to the model. You will have the assembly completed in a few minutes thanks to the mounting holes on the fuselage, which sit on the mounting parts of the chassis.

Recommended Spectrum transmitters for demanding pilots

To control larger and more demanding models, we recommend modern SPEKTRUM programmable transmitters of higher series:

• 8-channel DX Spectrum DX8e DSMX series transmitter with Smart Technology compatibility .
• 10-channel transmitter of the NX series Spectrum NX10 DSMX with the latest trends, voice output, Smart Technology compatibility, USB port .
• 20-channel transmitter of the iX Spektrum iX20 DSMX series with a large color 5 "touch screen, an Android interface with Czech and a transport case.

Recommended batteries

To power the model, we recommend a propellant LiPol battery with 4-6 cells (14.8–22.2V).

• For economical flying LiPo battery 4S Black Magic LiPol Car 14.8V 5000mAh 50C EC5 with EC5 connector.
• Higher power 6S Spectrum Smart LiPo 22.2V 4000mAh 50C IC5 with EC5 connector and Smart technology.
• Smart LiPo battery 6S Spectrum Smart G2 LiPo 22.2V 5000mAh 50C IC5 with Smart G2 technology
• For long flight and performance 6S Spectrum Smart G2 LiPo 22.2V 7000mAh 30C IC5 with Smart G2 technology

Spektrum batteries with Smart technology are currently the most modern and safest way to maintain and charge batteries. You can find the advantages of Spektrum Smart technology here.

Recommended chargers for conventional and Smart batteries

If you decide to use modern Smart LiPo batteries in RC aircraft models, then we recommend the following chargers:

• Charger with mains power supply Spektrum S1100AC with one output 1x100W .
• Charger with mains power supply Spektrum S2100 with two outputs 2x 100W .

Recommended modern chargers for Smart batteries

• High performance AC charger Spectrum Smart G2 charger S1400 1x400W AC with one 400W output.
• High-performance AC charger Spectrum Smart G2 charger S2200 2x200W AC with two 2x200W outputs.

There is a reduction for charging IC5 / IC3 Spectrum conversion cable IC5 device - IC3 battery 10cm 10 AWG.

Accessories for normal operation

For normal operation of flying RC models, you need suitable adhesives, a set of tools and a case for storing LiPol batteries. From our range, we recommend a quality set of 1.5 / 2.0 / 2.5 / 3.0mm Allen screwdrivers and Modelcraft Phillips screwdrivers (set of 6). Modelcraft mini pliers in a case (set) and a Modelcraft cutting knife with an A6 washer will certainly be suitable for assembly.

For quick repair of aircraft models, we recommend the fast-curing 4-minute Epoxy adhesive. From our offer we recommend Speed Epoxy 4 min. 71g

Protective covers for batteries

Protective covers are designed to reduce the risk associated with transporting and charging batteries. LiPo batteries can, while maintaining small dimensions and low weight, provide high discharge currents and have a large capacity. The LiPo battery is prone to mechanical damage and therefore needs to be thoroughly protected.