TA-2659
New product
Place to pick up | Delivery |
Store Českobrodska 566, Praha 9, 19800 | 03.04. od 15:00 |
Mode of transport | Delivery |
DPD Private- Delivery to the Czech Republic | 05.04. |
Czech Post | 04.04. |
PPL - Delivery to the Czech Republic | 04.04. |
Zásilkovna | 05.04. |
Balíkovna | 05.04. |
Mode of transport | Delivery |
DPD - Delivery to the Slovakia | 08.04. |
GLS - Delivery to the Slovakia | 08.04. |
PPL - Delivery to the Slovakia | 05.04. |
DPD - Delivery to Germany | 08.04. |
DPD - Delivery to Poland | 08.04. |
DPD - Delivery across Europe | 15.04. |
GLS - Delivery across Europe | 09.04. |
PPL - Delivery across Europe | 09.04. |
Zásilkovna SK - výdejní místa | 08.04. |
Zásilkovna SK - Packeta home | 08.04. |
Zásilkovna PL - na adresu | 08.04. |
Zásilkovna PL - paczkomaty | 08.04. |
Hermes DE - výdejní místa | 08.04. |
Rakouská pošta | 08.04. |
-24,43 €
Availability date:
The package contains a painted laminate model of the glider Avalanche 2.8m ARF, manual DE, EN.
RC model of the powerful and fast glider Avalanche 2.8m ARF with extremely high strength, thanks to the high proportion of carbon fibers in the entire structure. Designed for speed, tight fast maneuvers and dynamic aerobatics - for the ambitious model pilot with high demands!
The Robbe AVALANCHE is a fully GfK/CfK versatile electric glider with extremely high strength. This is achieved through selected components and a high proportion of carbon fiber in the overall construction. The two-piece extremely stiff wing is slid onto a large carbon rectangular spar in the fuselage that easily absorbs forces. An exciting flight experience for an ambitious model pilot, but due to the low load on the wing, you can of course also fly slowly.
The model Avalanche ARF Voll-GFK/CFK with a span of 2.8m Elektro from Robbe Modellsport has a wingspan of 2800mm and a weight of approx. 2690g (flying). The model is controlled using the functions M, S, V, K, Kl. Clean aerodynamic shapes, high performance, finished coloring. The model is designed as ARF - ALMOST READY TO FLY without electronics, drive, servos, cables, etc.
The version of the Avalanche ARF kit does not contain electronics or a motor, so you need to add your own equipment. There is enough space in the hull for the components needed to mount the drive, a propeller cone with a diameter of 38mm is recommended.
The butterfly tail surfaces slide onto the carbon clutch. The rudders have rudder levers inside the fuselage, the tail surfaces are therefore aerodynamically completely clean.
The Avalanche model is a kit in the ARF version, i.e. without equipment and electronics. It is therefore necessary to install a motor, a propeller with a cone, a regulator, a receiver, servos, a battery, extension cables 6x25cm, 2x75cm, and to have a transmitter and a charger available in the model.
For controlling aircraft models, we recommend the modern SPEKTRUM NX programmable transmitters:
If you decide to use modern Smart LiPo batteries in RC model airplanes, then we recommend the following chargers:
For the normal operation of flying RC models, you need suitable adhesives, a set of tools and a storage case for LiPol batteries. From our assortment, we recommend a quality set of 1.5/2.0/2.5/3.0mm allen screwdrivers and Modelcraft Phillips screwdrivers (set of 6). Modelcraft mini pliers in a case (set) will certainly come in handy for assembly, and for cutting a Modelcraft cutting knife with an A6 pad.
For quick repair of model airplanes, we recommend the fast-curing 4-minute Epoxy glue. From our offer, we recommend Speed Epoxy 4 min. 71g
Protective packaging is intended to limit the risk associated with the transport and charging of accumulators. LiPo accumulators, while maintaining small dimensions and low weight, can provide high discharge currents and have a large capacity. The LiPo battery is particularly susceptible to mechanical damage and therefore needs to be thoroughly protected.