Air Trainer 1.4m PNP 3-Axis Flight Stabilizer

Chassis with foam wheels

The undercarriage legs consist of two parts, they are attached to the fuselage with screws. The wheels are already installed on the chassis.

Mounting the spur

The controlled spur wheel holds the direction perfectly during take-off and landing. When mounting the rudder, the spur wire is slipped into the plastic pocket on the rudder rudder.

Control unit

Advanced electronics - a 3-axis gyroscope control unit - are installed in the fuselage, which will ensure straight-line flight and eliminate the effects of wind and turbulent environment.

Space for battery

Under the hinged cover in the lower part of the hull there is a space for the driving LiPol battery. A 3-cell with a capacity of 2200mAh - 300mAh is recommended. The connector used is Deans.

Aileron servos

Each wing half has its own aileron servo, levers, tie rods and servos with cables are already installed. Just assemble the wing, connect the V-cable and screw the wing to the fuselage.

Power unit

The 3720 880Kv AC motor and Robbe ECO Line 40A controller are installed in the hull, just assemble the propeller with cone and follower and the power unit is ready to go.

Recommended Spektrum transmitters

To pair the BNF version model, we recommend modern SPEKTRUM programmable transmitters:

• 
  
• 6-channel DX Spektrum DX6e DSMX series transmitter with telemetry, 250 models in memory .
  
• NX Spektrum NX6 DSMX 6-channel transmitter with the latest trends, Smart Technology compatibility, USB port and WiFi connectivity .
  
• 8-channel transmitter of the NX Spektrum NX8 DSMX series with the latest trends, Smart Technology compatibility, USB port and WiFi connectivity .
  

Recommended batteries

We recommend a 3-cell (11.1 V) LiPol drive battery to power the model.

• 
  
• Smart LiPo Battery Spektrum Smart G2 LiPo 11.1V 2200mAh 50C IC3 for Spektrum Smart Chargers
  
  
• LiPo battery Spektrum Smart LiPo 11.1V 2200mAh 50C IC3 for universal chargers
  
  
• For longer flight time LiPo battery Spektrum Smart LiPo 11.1V 3200mAh 30C IC3 with Smart technology
  

Spektrum batteries with Smart technology currently represent the most modern and safest way to maintain and charge batteries. The benefits of Spektrum Smart technology can be found here.

Recommended chargers for conventional LiPol and Smart batteries

If you decide to use modern Smart LiPo batteries in RC models of airplanes or helicopters, or to charge your batteries from other manufacturers, then we recommend the following chargers:

• 
  
• Network charger Spektrum S155 with one output 1x 55W .
  
• Network charger Spektrum S1100 with one output 1x 100W .
  
• Network charger Spektrum S2100 with one output 2x 100W .
  
• Network charger Spektrum S2200 with two outputs 2x 200W .
  

Accessories for normal operation

For the normal operation of flying RC models, you need suitable adhesives, a set of tools and a storage case for LiPol batteries. From our assortment, we recommend a quality set of 1.5/2.0/2.5/3.0mm allen screwdrivers and Modelcraft Phillips screwdrivers (set of 6). Modelcraft mini pliers in a case (set) will certainly come in handy for assembly, and for cutting a Modelcraft cutting knife with an A6 pad.

For quick repair of model airplanes, we recommend the fast-curing 4-minute Epoxy glue. From our offer, we recommend Speed Epoxy 4 min. 71g

Protective covers for accumulators

Protective packaging is intended to limit the risk associated with the transport and charging of accumulators. LiPo accumulators, while maintaining small dimensions and low weight, can provide high discharge currents and have a large capacity. The LiPo battery is particularly susceptible to mechanical damage and therefore needs to be thoroughly protected.