Traxxas Ford Fiesta 1:10 BL-2s 4WD RTR Blue

AC drive BL-2S

The BL-2s AC drive with a 3300rpm/V motor increases speed and acceleration by up to 60% compared to other DC motor drives. Improved efficiency, high-speed ball bearings and an internal cooling fan give the motor long life with minimal maintenance.

Extreme Heavy Duty kit installed

The Factory Installed Extreme Heavy Duty Kit on the Rally Ford Fiesta replaces key drivetrain and suspension components with upgraded parts built for maximum strength and durability.

Clipless bodywork

The unique body attachment system using beaks on the sides of the model (at the thresholds), allows quick and easy battery replacement, and the clean look of the model is not disturbed by clips.

Modular chassis construction

The modular design allows the entire front section to be removed by loosening 5 screws and the rear assembly to be removed by loosening 4 screws. In less than one minute you have full access to easy service and setup.

Chassis

The chassis of the model made of durable composite nylon is equipped with a long wheelbase and a reduced center of gravity for greater stability. On the underside, the chassis is smooth, so that it does not trip over bumps. The weight was also optimally distributed, where the majority of the mass is stored along the line of the chassis.

Metal differentials

The new Ford Fiesta is equipped with quality metal gear differentials that are fully prepared for the power of AC drive and even upgrade to VLX-3S. Precision sealing with X-rings allows differentials to be tuned for specific operating conditions by changing fluid viscosity.

Long shrug

The long stroke of the shoulders dampens even sharp impacts and improves the controllability of the model. In every situation, it will have a precise and quick steering response. Adjustable oil shock absorbers are used on the chassis for endless fun.

Friction clutch

The friction clutch uses a special semi-metallic friction material and aluminum alloy pressure plates to dissipate heat and ensure consistent traction control. The clutch slip intensity can be adjusted without disassembling the model.

Oil dampers

The long stroke Ultra Shock oil shocks are designed to absorb every impact. Double sealing X-rings ensure smooth operation without oil leakage. The properties of the shock absorbers can be changed by preloading the springs, or by replacing the springs with other ones, and the behavior of the shock absorbers can also be adjusted by changing the viscosity of the oil used.

Precise steering

The mechanics of turning the front wheels is realized by means of the Dula-Bell-Crank system, which ensures the precise movement of the rods to the wheels. The steering has an integrated servo-saver that absorbs shocks and protects the servo against overload.

Rally wheels and tires

The durable rally-style twelve-spoke wheels feature a 12mm dropper and the same offset as the wheels on the Slash 4x4 models. The tires have a unique directional pattern with high grip on and off hard surfaces.

Servo steering

Digital servo standard size Traxxas servo 2056 6.2kg.cm waterproof with DC motor and nylon gears has a torque of 6.2 kg.cm and a speed of 0.20 s/60°@ 6.0 V. For water resistance*, the servo box is fitted with a seal.

AC motor 3300kv

The Traxxas 3300kv AC motor provides the ideal affordable drive for 1:10 models with all the benefits of high performance, long life and minimal maintenance. The motor is equipped with a Quick Connect connector for easy connection. Other features include:

• 
  
• Integrated cooling fan
  
• High speed ball bearings
  
• High acceleration
  
• Efficient operation for longer driving time
  

Electronic regulator BL-2S

Waterproof* electronic BL-2S AC controller with three driving modes, 2S LiPo battery support and easy EZ-Set™ button control. The regulator is equipped with a training mode that limits full throttle to 50%. Thanks to this, novice drivers or children can gradually familiarize themselves with the features of the model and prepare for the full power of the car. Thermal protection, protection against underdischarge of LiPo batteries, gold-plated connectors, simple operation, intuitive signaling with a two-color LED diode and a powerful cooler that can be supplemented with an optional fan (not included in the package).

BL-2S controller modes

• 
  
• Sport : Default mode, forward, braking and reverse are possible.
  
• Race : Mode suitable for racing. Forward and brake is possible; reverse is not available.
  
• Training : Mode suitable for children or novice riders. It is possible to drive forward with a power limitation of 50%, brake and drive backwards again with a power limitation of 50%.
  

Traxxas TQ RC Kit

The model is controlled by a two-channel proportional steering wheel RC radio Traxxas TQ, working in the 2.4 GHz band - operation without interference. The transmitter is powered by only 4 AA cells.

There is a rotary knob on the transmitter that trims the steering (so that the model goes straight if the steering wheel is in the center position). The status of the batteries in the transmitter is indicated by an LED. Reverse can be set on the transmitter on the throttle and steering channels.

TQ receiver

The Traxxas TQ 2.4 GHz three-channel receiver ensures safe driving without interruptions. Easy pairing with one button. Status indication by means of an LED diode.

Recommended LiPo batteries:

With modern LiPo batteries, the model will have maximum acceleration. The model can be operated on a 2-cell (7.4 V) LiPo battery.

• 
  
• For higher performance Traxxas LiPo battery 7.4 V 5000 mAh
  
• For higher performance and long driving time Traxxas LiPo battery 7.4 V 7600 mAh
  

Recommended NiMH batteries:

NiMH batteries do not require precise handling and are therefore suitable if the RC model car is operated by children (NiMH batteries are not destroyed by complete discharge). However, NiMH batteries do not provide such performance.

• 
  
• NiMH battery Traxxas 8.4 V 3000 mAh (flat)
  
• For longer driving time Traxxas NiMH battery 8.4 V 5000 mAh (flat)
  

Recommended Traxxas Chargers

Traxxas universal chargers can charge Traxxas LiPo and NiMH batteries. Traxxas chargers are a simple and safe way to charge batteries. Traxxas uses the unique iD system , so you're always sure to connect everything easily and safely. There is an integrated chip in the battery connector, which the Traxxas charger automatically recognizes and sets all battery charging parameters for you. More information here.

• 
  
• Traxxas EZ-Peak 50W Single Output Mains Charger
  
• Traxxas EZ-Peak 2x50W mains charger with 2 outputs
  

Carrying bag and backpack

Carry the RC model comfortably and safely in a Traxxas sports bag or backpack. In addition to the main large pocket for the model, there are specially designed side pockets for batteries, charger, tools, etc.

Stand

The aluminum swivel stand will be the perfect addition to your service table or display shelf. The stand facilitates the maintenance of the model and at the same time prevents the deformation (stretching) of the tires during long-term standing.

Work mat

Work mat 91x51cm, for service of RC models and other modeling work. Prevents damage to the workbench, resistant to chemicals. Practical compartments for organizing parts and tools.

Accessories for normal operation

For normal operation of the Traxxas RC car, you need bolt glue, good quality tire glue, silicone shock oil and a set of screwdrivers. We recommend an affordable set of tools for cars from our range.

The thread or head of the screw is dripped with screw glue, which fixes it and the vibrations caused by driving will not allow the screw connection to loosen. The screw adhesive has a special composition that allows the screw connection to be easily loosened with an adequate torque without damaging the screw head. Never use ordinary instant glue, it might be impossible to loosen a screw stuck like this!

Tire glue is used to glue the tires to the disc rim. It is always necessary that the tire is firmly stuck to the wheel rim all the way around! If the tire is not glued all the way around, it may tear. Tire glue has a special composition that is able to glue materials such as rubber or nylon, and at the same time, after hardening, the glue is flexible. Never use ordinary instant glue - it is not flexible after hardening and cracks would gradually form in the tire around the rims!

Sometimes it is necessary to add silicone oil to the dampers of the model. During normal operation, there are only slight leaks of silicone oil on the piston rods of the shock absorber. In the event that the surface of the damper pistons or the condition of the seals is in poor condition, the oil leakage may be large. For these cases, so-called repair kits are supplied. In the range of tuning parts, piston rods with an extremely hard TiN (titanium nitride) coating are delivered to all shock absorbers. Piston rods with a TiN surface are easily recognized by their golden-green color.