The RC model car Arrma Senton 3S BLX in 1:10 scale is ideal for off-road and asphalt. Thanks to the powerful AC motor, the model reaches speeds of up to 80 km / h. Driving time about 20 minutes on LiP
The package contains an RC model car Arrma Senton 3S BLX 1:10 4WD RTR with installed components: AC motor Company 3200Kv 4-P BL3660Kv, regulator Arrma BLX100, Spektrum servo S651 7kg MG. Transmitter Spektrum SLT3 2.4GHz, multilingual manual in English, German, French and Italian and instructions in Czech.
Characteristics
RC car model Arrma Senton 3S BLX 1:10 4WD RTR Short Course Truck. Powerful AC motor Spectrum ™ Company ™ 3200Kv waterproof regulator Arrma BLX100 with fan 2S / 3S LiPol, servo control S651WP MG. RC set Spectrum ™ SLT3 ™ 2.4GHz with SLR300 receiver.
The remote-controlled car model with a center engine and 4x4 drive will provide maximum traction and performance on any surface. Model speed up to 80 km / h.
The RC model of the Arrma Senton 3S BLX 1:10 4WD car surprises with its toughness and durability. It has a stronger chassis, a more powerful servo, a transmitter with an ergonomic grip for fatigue-free driving, a steering wheel with foam rims for precise control. New drivers can set the throttle limit to 50% or 75% until they are ready to use their full speed potential. The SLT3 ™ transmitter is compatible with Tactic® SLT ™ receivers for the operation of older Arrma RTR cars and has a third channel to control optional functions such as lights and winches. The monster truck with all-wheel drive is equipped with a powerful AC motor BLX 3200KV, which gives the model an endless stream of power. To prevent the RC model from tipping over when adding throttle, it is equipped with rear wheelies. The controller, with support for 3S LiPo batteries, provides a choice between three driving modes, just choose and start racing. / p>
Reinforced chassis
Several changes in reinforcement were made on the chassis, for greater rigidity. At the same time, aluminum was used on the axle pin retaining plates. The chassis design is arranged in a proven component layout to achieve a perfect balance. Drive shaft in the middle, battery on one side and electronics on the other. In addition, the entire chassis is equipped with side covers that limit the ingress of dirt into the chassis. The battery is firmly seated in place with straps.
Larger handle on the drive module
The area of the "Pull" board has been increased for better mounting and handling of the drive module.
Pinion with driven gear
The motor can be adjusted and the inter-tooth clearance precisely adjusted when replacing the pastor or gear, thanks to the aluminum plate with grooves for mounting the motor.
Ball bearings
All rotating parts are mounted in ball bearings. Exposed bearings are protected against dust and dirt by rubber caps.
Servo saver for servo protection
The model received a new more powerful servo saver and a new more efficient servo saver was used for its maximum protection. This provides a higher level of impact protection and safer driving.
Grooved shafts
As with the 4S version, grooved shafts are used here, which can easily transmit the high power of the AC motor. / p>
Wheels and tires
Robust, multi-spoke discs with dBoots® Fortress-SC tires with a distinctive pattern, give the RC model car Senton 3S BLX Short Course Truck maximum grip on all surfaces.
Oil dampers
Patented oil dampers absorb every impact of the model. The shock absorbers are equipped with impact protection covers on the front. The change in stiffness and ground clearance is possible with the aid of oil viscosity or spacers. silicone O-rings are used for safe oil retention.
Compact chassis
The chassis design is arranged in a proven component layout to achieve a perfect balance. Drive shaft in the middle, battery on one side and electronics on the other. In addition, the entire chassis is equipped with side covers that limit the ingress of dirt into the chassis. The battery is firmly seated in place with straps.
Front and rear differential
The model is equipped with front and rear differentials, which ensure maximum traction. The differentials are equipped with high-quality metal gears for trouble-free operation. The wheel drive is transmitted by means of telescopic half-axles.
Flexible bumper
The front of the Senton 3S BLX protects against impact from a flexible frame bumper that is mounted at four points. In case of damage, the bumper can be easily replaced.
The drive unit consists of a Firma 3660 AC motor and a BLX100 AC controller. Each of these units forms a separate modular system.
Easily accessible engine module
The engine module is removed from the chassis as a complete unit, removing one bolt. Includes engine, engine plate, clutch assembly and transmission cover.
Easy disassembly of the electronics module
The electronics module consists of a waterproof receiver box, servo board and controller holder. The unit is dismantled and is available for maintenance and service needs.
Front and rear differential
The model is equipped with front and rear differentials, which ensure maximum traction. The differentials are equipped with high-quality metal gears for trouble-free operation. The wheel drive is transmitted by means of telescopic half-axles.
Fixed shock absorber towers
The pins at the ends of the shock absorbers are fixed in the shock absorber towers on both sides, therefore they do not twist and a stronger fastening of the shock absorbers is guaranteed.
Digital Servo Control Spectrum MS SPMS651 MG
New Servo for Directional Control The Spektrum S651 7kg MG MG has 15% more torque than the previous ADS-7M servo. It is waterproof, has metal gears and a torque of 7.27 kg.cm at 6V.
pg ">
BLX 3660 AC motor
The model is powered by a powerful 4-pole AC motor BLX 3660 3200 rpm // V. The four-pole design gives the motor a linear course from low speeds. The metal black anodized case not only looks amazing, but also allows better heat dissipation to the passive cooler. 4 mm pin connectors allow easy disconnection for easy engine maintenance.
Power supply up to 3S LiPol
Very smooth operation thanks to the 4-pole design
Gold-plated connectors for perfect current transfer
Shaft O 5mm
BLX100 electronic controller
The BLX100 AC regulator with a current load of up to 100A, in combination with 3S LiPo batteries will provide incredible power. The built-in fan ensures sufficient cooling even at full load. The controller has driving modes, protection against battery undercharge and overvoltage protection. Voltage BEC 6V. Waterproof * switch on the controller. Battery connector IC5.
Adjustable parameters:
Switching voltage: NiMH / LiPo
Acceleration: in 7 steps. Tip: On slippery surfaces, it is better to use less acceleration to prevent the wheels from slipping
Brake forces: 25%, 37.5%, 50%, 62.5%, 75%, 87.5% and 100%
Mode: Forward / brake / reverse or forward / brake
Direction of motor rotation: Normal or reverse
New IC5 connectors
The new IC5 connectors have a modern design with an emphasis on safety and simplicity. The contacts are made of gold-plated pins and sockets with a diameter of 5 mm.
As already mentioned, the connectors have been designed with an emphasis on safe and easy use. The connectors cannot be reversed in polarity, the contacts and soldered connections are covered with a plastic cover. The IC5 connector is backward compatible with EC5.
Transmitter Spectrum SLT3
The basic 3-channel Spektrum SLT3 steering wheel operating at 2.4 GHz is compatible with the SLT protocol. The low weight of the Spektrum SLT3 transmitter allows for fatigue-free holding. The steering wheel is covered with a foam rim for a firm grip. The layout of the controls is practical and intuitive - all controls are positioned so that they are quickly accessible when needed. A secure loop is available for attachment to the strap.
3-channel steering wheel RC set Spektrum SLT for reliable control
Proven design for comfortable grip without fatigue
Possibilities of limiting the maximum deviations of the control channel and gas
Dual steering channel deflections and 50%, 75% and 100% engine power limiter
You can use the third channel for additional devices, eg for sound modules.
SLR300 receiver with SLT-FHSS protocol
The car 3-channel receiver SLR300 is equipped with SLT FHSS 2.4GHz technology, resistant to interference. It is compatible with Spektrum SLT transmitters and is backward compatible with Tactic steering wheel transmitters.
* For information on water resistance specifications, refer to the operating instructions. Tips and tricks for operating in a wet environment can be found in the blog.
We recommend buying
To put the model into operation, 4x AA batteries for the transmitter, a drive battery and an adequate charger for the drive battery are required.
Recommended LiPo batteries
The model can be operated on a 2 to 3 cell LiPo battery or a 7 cell NiMH battery. The battery should be equipped with an EC5 or IC5 connector. For normal riding, we recommend a 2-cell LiPo battery (7.4 V).
For normal riding LiPo battery Spectrum 7.4 V 5000 mAh with Smart technology.
For the maximum possible speed of LiPo battery Black Magic LiPo 11.1 V 5000 mAh.
For the maximum possible speed of LiPo battery Spectrum LiPo 11.1 V 5000 mAh with Smart technology.
Spektrum batteries with Smart technology are currently the most modern and safest way to maintain and charge batteries. You can find the advantages of Spektrum Smart technology here.
Recommended NiMH batteries
NiMH batteries are not demanding on precise handling and are therefore suitable if the RC model of the car is operated by children (NiMH batteries are not destroyed by complete discharge). However, NiMH batteries have a lower capacity, so driving time will be slightly shorter.
Recommended chargers for conventional and Smart batteries
If you decide to use modern Smart LiPo batteries in the RC model of the Arrma car, then we recommend this charger:
Charger with mains power supply Spektrum S150 with one 1x50W output.
Mains charger Spektrum S1100 with one 1x100W output.
Mains charger Spektrum S2100 with two outputs 2x 100 W. <
To connect the battery to these chargers, you need an IC5 / IC3 charging adapter.
High-performance mains charger Spektrum Smart G2 charger S1400 1x400W AC with one 400W output.
High-performance mains charger Spektrum Smart G2 charger S2200 2x200W AC with two 2x200W outputs.
Accessories for normal operation
For normal operation of an RC car, you need tire glue, screw glue, a set of tools and silicone oil for the shock absorbers. From our range we recommend an affordable set of tools for RC cars.
The tire glue adheres the tires to the rim of the disc. It is always necessary for the tire to be firmly glued to the wheel rim around the entire circumference! If the tire is not stuck around the entire circumference, it may rupture. The tire adhesive has a special composition that is able to bond materials such as rubber or nylon, and at the same time, after hardening, the adhesive is flexible. We recommend Robitronic Tire Glue from our offer - see recommended accessories.
Occasionally it is necessary to add silicone oil to the model's shock absorbers and change the oil in the differentials. During normal operation, there is only a slight leakage of silicone oil along the shock absorber piston rods. If the surface of the shock absorber piston rods or the condition of the seals is in poor condition, the oil leakage can be large. For these cases, repair kits or individual parts are supplied. From our offer of silicone oils, we recommend silicone oils TLR (Team Losi Racing), see recommended accessories.
Screw adhesive is required for routine maintenance. Screws screwed into the metal material (eg screws in the motor, set screw in the pinion) must be secured against loosening with this adhesive.
Protective covers for batteries
Protective covers are designed to reduce the risk associated with transporting and charging batteries. LiPo batteries can, while maintaining small dimensions and low weight, provide high discharge currents and have a large capacity for long travel times. On the contrary, the LiPo battery is prone mainly to mechanical damage.
Arrma universal metal wrench 5 / 7mm, 11 / 15mm, for Arrma cars for nuts and shock absorber sealing sleeves, for mounting 5mm, 7mm and 12mm nuts. The 12mm wrench can be used to set the friction clutch
Versatile, affordable, easy-to-use 2-to-4-cell LiPo, LiFe, LiHV and 6 to 8-cell NiMH battery chargers. Adjustable charging current 1, 2, 3, or 4 A, status indication
Special fixing adhesive for securing screws, which prevents spontaneous loosening of the screw connection. The adhesive has high strength, withstands high temperatures.
Special instant glue Robitronic Tire Glue designed for gluing tires to RC car discs. The adhesive is flexible after solidification, thus minimizing the risk of the tire tearing at the joint. O
Spektrum conversion cable with connectors IC5 device (male) - IC3 battery (female), length 10cm, cable 10 AWG. Can be used to charge Smart batteries with IC5 connector Spektrum Smart chargers with only IC3 output. Cable including data cable.
Mains switched stabilized power supply Spectrum power supply 24 V 16 A for powering chargers or other devices. The cooling fan is active with automatic speed control, overtemperature protection, over
Spektrum Smart S100 USB-C charger with power up to 100W, new user interface and integrated connectors IC3 and IC5. Charges batteries 1-4 cells LiPo, LiIon, LiHV, LiFe and 1 to 12 cells Smart NiMH batteries. Charging current up to 6 A.
The new generation Spektrum Smart S1200 1x200W AC charger with SMART technology brings the most modern user-friendly environment, button control, output with IC3/IC5 connectors and a 320 × 240 IPS LCD display. USB output 5V / 2A. Modern ergonomic...
Spektrum Smart S2200 2x200W AC charger of the new generation with two outputs of 200W each and SMART technology, brings the most modern user-friendly environment, button control, output with IC3/IC5 connectors, 320 × 240 IPS LCD display and USB output...
Metric set of screwdrivers and wrenches ideal for Losi, Traxxas, Cen, Kyosho, etc. The hobby set consists of a total of 17 interchangeable bits, wrenches and handles.
Team Losi Racing silicone oil for differentials with a viscosity of 10000 cSt with additives to reduce gear wear. Packed in a practical tube, volume 30 ml.
Team Losi Racing silicone oil for differentials with a viscosity of 30000 cSt with additives to reduce gear wear. Packed in a practical tube, volume 30 ml.
AC electric motor BLX3660. Four-pole motor, 3200rpm, designed for use with the ARRMA BLX100 controller. Aluminum body for better cooling. 4 mm connectors. The drive surface is ground on the shaft.
Arrma chassis block, multifunctional tool: 4x4 can be used for maintenance and adjustment of RC models of Arrma cars. Includes 7mm and 8mm wheel nut wrenches.
Spare part for RC car models Arrma: differential box, gear 37T: 4x4 BLX. Suitable for 1:10 Granite 3S, Senton 3S, Big Rock 3S, Kraton 4S, Outcast 4S models.
Spectrum servo standard size S651. Metal gears, waterproof, power supply 6-7.4V, moment 6.3-7.4kg.cm, speed 0.143-0.122s/60°, dimensions 40x20x39.4mm. Thousand-sided 23T. Replacement for the ADS-7M servo.
Install the extra durable Arrma metal differential BOOST Box to your 4X2 BOOST, MEGA or 3S basher RC car. The package includes full metal front and rear differentials with full metal bevel gears, input gear and internal gear.
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 13T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 14T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 15T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Arrma pinion for shaft 5 mm (1/8 ") with 15 teeth and gear module 32DP (0.8 mm) for RC car models. Made of sintered steel. The package includes a worm.
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 16T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 17T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 18T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 19T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 20T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 21T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 22T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 23T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 24T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 25T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 26T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 27T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 28T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 29T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 30T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 31T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
Tuning part for RC car models Arrma 3S 4WD Bigrock, Granite, Senton, Typhon: pinion 32T 0.8M Safe-D5. The shaft hole with the D-shaped surface ensures a firm connection even when the pinion is release
ARRMA BOOST BOX option kits make it easy to upgrade your RC car for higher performance and more durability. Upgrade your 4X2 BOOST or MEGA car with the ARRMA metal BOOST Box slip clutch. Add your AC controller and motor!
Tuning highly durable and stylish Pro-Line arms front blue for RC car models Arrma 3S - Granite, Senton, Vorteks, (incl. Boost 4x2, Mega 550). Made of strong nylon. They contain several mounting points for shock absorbers. The arms are part of the Bash...
Pro-Line body clear 980 Chevy Pick-up: Monster Truck, for RC car models in 1: 8 scale, wheelbase 310mm, length 470mm, width 175mm. Made of durable 1.5 mm lexan.
Pro-Line body clear 1972 Chevy C-10 Long Bed: Monster Truck, for RC car models 1: 8, wheelbase 320mm, length 475mm, width 180mm. Made of durable lexan. Suitable for Monster Truck 1: 8.
Pro-Line body clear 2021 Chevrolet Silverado 2500 HD, for RC Monster Truck car models in 1:10 scale, wheelbase 321mm, length 457mm, width 178mm. Made of durable lexan.
Pro-Line body clear 2020 Ram Rebel 1500, for RC car models ARRMA Kraton 6S in scale 1: 8, wheelbase 321mm, length 464mm, width 181mm. Made of durable lexan.
Pro-Line body carved clear 2020 Ram Rebel 1500, for RC car models E-REVO 2 in scale 1: 8, wheelbase 321mm, length 492mm, width 181mm. Made of durable lexan.
Pro-Line body clear 1978 Chevy C-10 Race Truck, for RC models of Short Course cars in scale 1:10, wheelbase 330mm, length 521mm, width 292mm. Made of durable lexan.
Pro-Line bodywork clear Chevy Silverado HD: Slash, SC10, for RC car models in 1:10 scale for Slash® 2WD and Slash® 4x4. The body has a wheelbase of 330mm, length 521mm, width 292mm. Made of durable le
Pro-Line body clear 2019 Chevy Silverado Z71 Trail Boss, for RC models of Short Course cars in scale 1:10, wheelbase 330mm, length 521mm, width 292mm. Made of durable lexan.
Pro-Line body clear 1984 Dodge Ram 1500 Race Truck, for RC models of Short Course cars in scale 1:10, wheelbase 330mm, length 528mm, height 160mm. Made of durable lexan.
Pro-Line black body Flo-Tek Fusion Black, for RC models of Short Course cars in scale 1:10, wheelbase 323mm, length 546mm, width 235mm. Made of durable lexan.
Pro-Line body clear cut Flo-Tek Fusion, for RC models of Short Course cars in 1:10 scale, wheelbase 323mm, length 546mm, width 235mm. Made of durable lexan.
Pro-Line body clear 1981 Ford Bronco, for RC models of Short Course cars in scale 1:10, wheelbase 330mm, length 528mm, width 295mm. Made of durable lexan.
Pro-Line body clear 1966 Ford F-100, for RC models of Short Course cars in 1:10 scale, wheelbase 323mm, length 516mm, width 239mm. Made of durable lexan.
Pro-Line body carved clear 1967 Ford F-100 Race Truck, for RC models of Short Course cars in scale 1:10, wheelbase 325mm, length 528mm, height 157mm. Made of durable lexan.
Pro-Line body black Ford F-100 Heatwave, for RC models Short Course cars in scale 1:10, wheelbase 325mm, length 528mm, width 295mm. Made of durable lexan.
Pro-Line body clear 1979 Ford F-150 Race Truck, for RC models of Short Course cars in scale 1:10, wheelbase 330mm, length 521mm, width 292mm. Made of durable lexan.
Pro-Line body clear 2017 Ford F-150 Raptor mock-up, for RC models of Short Course cars in scale 1:10, wheelbase 330mm, length 550mm, width 240mm. Made of durable lexan.
Pro-Line body clear Jeep Gladiator Rubicon, for RC models of cars Short Course and Monster Truck in scale 1:10, wheelbase 330mm, height 478mm, width 142mm. Made of durable lexan.
Pro-Line body clear Megalodon Desert Buggy, for RC models of Short Course cars in 1:10 scale, wheelbase 335mm, length 483mm, width 191mm. Made of durable lexan.
Pro-Line body clear Toyota Tundra TRD Pro True, for RC models of Short Course cars in scale 1:10, wheelbase 330mm, length 546mm, width 279mm. Made of durable lexan.
Pro-Line body clear VW Baja Bug: Short Course, for RC car models in 1:10 scale, wheelbase 318mm, length 490mm, width 191mm. Made of durable lexan. Equip your Slash® body with a VW® Baja Bug body.
Pro-Line body clear VW Full Fender Baja Bug: Short Course, for RC car models in 1:10 scale, wheelbase 318mm, length 500mm, width 178mm. Made of durable lexan.
Complete Pro-Line wheels for 1:10 RC model cars. Size ?115x48 mm. The Raid disk is black in color. Dumont 2.2"/3.0" SC front paddle tires. The driver is a 12 mm hexagon. Closed cell insert.
The high-performance RC model car Arrma Vorteks 3S BLX in 1:10 scale with 4WD drive is the fastest and most advanced ARRMA® model for adrenaline experiences. A car with the advantages of intell
