Express delivery
Large selection of carriers
Satisfaction guarantee
CCPM swashplate controlled by electronically mixed servos, flybarless "paddleless" rotor head with a 3G three-axis gyroscopic system instead of the usual mechanical stabilizer and gyro stabilizing the helicopter around the vertical axis, powerful brushless motor and electronic speed controller with governor function, intelligent control unit allowing operation in a tilt stabilization mode suitable for helicopter beginners as well as in 3D mode for wild aerobatics without limits - all this can be found in the M1 V1 microhelicopter with a 290 mm diameter main rotor!
The basis of the fuselage construction is made up of duralumin engine mounts and a main shaft housing with a two-piece plastic fuselage frame, plastic skid landing gear and tail beam made of profiled duralumin tube with a carbon vertical stabilizer. The frame houses a Sunnysky® R23-2 AC electric motor with a rotating casing that drives the main rotor directly, without the usual gears. The balancing rotor is also driven directly by a miniature Sunnysky® R08-2 AC motor. This makes the entire mechanics as simple as possible, eliminating problems with rubbing slides, brushed gears or slipping drives.
The robust 3 mm main shaft is mounted in ball bearings. The swashplate is made of duralumin, as is the rotor head with blade carriers. Thanks to the 3G flybarless system and the electronic CCPM, the rotor head is very simple. The main rotor blade carriers are a beautiful miniature of the carriers of "big" RC helicopters - with all those ball bearings and damping inserts!
The helicopter's electronics consist of an intelligent control unit with an integrated 3G flybarless control unit, an electronic speed controller with a governor function and three DS2045 digital picoservos with metal gears controlling the CCPM (120°) mixed swashplate. To control the helicopter, you will need at least a six-channel RC kit with a miniature receiver with an S.BUS port (or also DSM/DSMX). For ordinary flying, the transmitter does not even have to be a computer transmitter (all the necessary mixes are provided by the control unit), only 4 channels "on the sticks" and a fifth channel with a two-position switch for switching the control unit modes with stabilization and 3D are enough. Of course, for full-fledged classic and 3D flying, a computer transmitter with adjustable 2-3 flight modes with at least five-point collective curves for hovering and aerobatics and another mode for autorotation is needed.
The easily removable sports cabin is made of a very lightweight molded durable plastic - you can choose from two color schemes that guarantee good visibility and "readability" of the helicopter's position in the air. The helicopter is powered by a two-cell LiPo battery 7.4 V 350 mAh with a 50C load capacity (with JST-XH connector) located on the underside of the fuselage. It will provide you with up to 9 minutes of simple flying or up to 4 minutes of aggressive 3D aerobatics.
The helicopter is delivered fully assembled with a preset control unit, so you just need to unpack the helicopter, connect your S.BUS compatible receiver, charge the drive battery, set up your transmitter according to the detailed instructions with illustrative pictures, check all the functions of the helicopter - and you can take off!
The M1 V1 is a full-fledged 3D helicopter with a controlled collective - and as such it assumes and requires appropriate piloting experience. It is not a "drone" that you just add gas to, it takes off and hangs "like nailed" without any intervention in the controls. The M1 V1 will be fully enjoyed by intermediate to advanced pilots who already have experience flying helicopters with a controlled collective ("six-channel"). However, with enough perseverance, humility, prior diligent training on a computer RC simulator, under the supervision of an experienced pilot and using the stabilized mode, even a novice helicopter pilot can start flying the M1 V1.
The ARF helicopter set includes: 100% assembled and ready-to-fly M1 V1 model, LiPo 7.4 V 350 mAh 50C battery, Allen screwdriver, flat wrench, charging cable, a solid EPP foam box with a hinged lid for safe transportation and storage of the model, instructions for operating the model and setting up the control unit.
