Axial SCX10 III Jeep JT Gladiator 4WD 1:10 RTR gray

V8 engine mock-up cover

The faithful model of the V8 engine with the gearbox purposefully hides and protects your electric motor and at the same time enhances the realistic appearance of the chassis and motor unit. For maximum strength, the engine bed is aluminum.

Portal axles with hypoid transmission

The advantage of the AR45 gantry axles is, of course, the higher ground clearance, but also the advantageous reduction of the torque on the output shaft and the reduction of the torque and load of the drive train components.

3-piece body

The Jeep® JT Gladiator body consists of three parts, which makes it easier to install the cockpit, battery access and chassis components.

Highly detailed finished lexan body

The body of the car model is an exact replica of a real car, so the body clips are hidden so as not to disturb the body lines. Jeep® JT Gladiator has a detailed interior, steering wheel and driver's figure, lots of details on the body, such as front grille, hood air intakes, wipers, door handles, rear-view mirrors, fenders, rear door hinges, car lighting with glazing, including turn signals, etc. .

New battery bed

The SCX10-III chassis has a propulsion battery located near the center of the chassis, which offers a more balanced chassis with the engine at the front. There is also space on the side rails for smaller batteries, which are needed for other accessories such as lighting, winch and the like.

Aluminum oil shock absorbers

Long-stroke shock absorbers have a body made of anodized aluminum, the coil springs can be set to the force of the pressure to achieve the optimal degree of damping (spring preload can be conveniently regulated using a nut on the shock absorber body). The caps have a screw hole for checking the condition and filling of the oil. Thanks to the size and volume of the shock absorbers, their function is guaranteed along the entire stroke length.

Stainless steel ball joints

Axial used higher quality materials in the new SCX10 III chassis to maintain the highest standard of service life. The ball joints on all chassis hinges are made of stainless steel for higher accuracy and chassis rigidity.

Geometry setting options

The Axial® team continues to optimize the geometry settings of the chassis, which is mounted on four arms. He used the experience of the SCX10 II chassis and improved the geometry of the gantry suspension, which helped to further reduce torque and at the same time allow you to tune the chassis to your liking.

Longer chassis frame

The design team increased the wheelbase to 353mm longer frame rails and chassis tie rods, allowing Axial® to design a realistic Jeep® JT Gladiator.

Detailed interior with driver

Thanks to the well-thought-out design of the chassis, the body has space for the cockpit with the driver. In this space there is a realistic driver figure, dashboard and seats.

Rear body mounting

Body disassembly has been facilitated by a new rear bumper design with body pin holes.

Licensed 3-piece beadlock discs

The officially licensed KMC XD Machete discs, which are famous in the field, are stamped in satin chrome and contain amazing model details. Because they are three-piece discs, the tires can be easily mounted, removed and replaced without gluing.

Servo shift

On the third channel of the DX3 transmitter, you can use the switches for shifting the servo speed of the SX107 gearbox with controlled DIG function.

Receiver and controller in one

The controller and receiver are integrated in one box SPEKTRUM ™ FIRMA ™ SMART 40A. Thanks to the latest electronics used, you can take advantage of telemetry and the exclusive Spektrum-Smart technology. Install the LiPol Spektrum Smart battery to keep track of the battery status on the transmitter voltage level indicator.

RC transmitter Spectrum DX3 2.4GHz DSMR

The new RC transmitter Spektrum DX3 has 3 channels and is compatible with the Spektrum AVC stabilization system and Spektrum Smart telemetry. Excellent range, super fast response and high resistance to interference thanks to the exclusive Spektrum DSMR technology. Quick setting of required parameters.

• LED indication of the state of charge of the Smart batteries in the model
• Support of the Spektrum AVC stabilization system
• Possibility to set reversal, size of deviations and function of the 3rd channel
• Trim gas channel and control
• Thanks to the gas limiter, you can limit the maximum speed of the model for children
• Ergonomic, lightweight
• Foam rim steering wheel for a comfortable grip

SMART technology

Smart technology ensures that all the electronics in your aircraft model work together seamlessly. It offers information on the status of drive electronics components, increases your confidence in its capabilities and makes the entire drive system easy to use. The Smart system consists of a compatible Spektrum transmitter, Smart receiver, Smart controller, or Smart battery.

Recommended LiPo batteries

For normal riding, we recommend a 2 or 3 cell LiPo battery (7.4 V, 11.1 V), with EC3, IC3 connector.

• Smart LiPo battery Spectrum 7.4 V 5000 mAh
• Standard LiPo battery Black Magic 7.4 V 5000 mAh.
• Standard LiPo battery with maximum driving time Black Magic 7.4 V 6500 mAh.
• For a larger speed range Smart LiPo battery Spectrum 11.1 V 5000 mAh

Spektrum batteries with Smart technology are currently the most modern and safest way to maintain and charge batteries. You can find the advantages of Spektrum Smart technology here.

Recommended NiMH batteries

NiMH batteries are not demanding on proper handling and are therefore suitable if the RC model car is operated mainly by children (NiMH batteries will not be destroyed by complete discharge). However, driving time with NiMH batteries will be a bit shorter.

Recommended Chargers for Spectrum Smart Batteries

If you decide to use modern Smart LiPo batteries in the RC model of the Axial car, then we recommend this charger:

• Charger with mains power supply Spektrum S150 with one output 1x50W. <
• Mains charger Spektrum S1100 with one 1x100W output.
• Mains charger Spektrum S2100 with two outputs 2x 100 W.

Recommended chargers for conventional LiPo and NiMH batteries

If you decide to run the model on conventional LiPo and NiMH batteries , we recommend using universal chargers with a power of at least 50 W.

• Dynamite Prophet Sport charger with one 50 W output
• Robitronic Expert LD 80 AC / DC charger with one 80 W output + EC3 charging cable

Shipping bag

Carry the RC model comfortably and safely in a Robitronic carrying bag. The bag is airtight and has an elastic edge that can be adjusted to the model. Thanks to the Velcro strap, the model is easy to carry. The synthetic material can be easily cleaned with water or soap suds if required.

Model lighting

For a breathtaking appearance, we recommend equipping the model with LED lighting. If the model already contains basic lighting, you can expand, improve or modify it according to your own needs.

• Light set Axial LED lighting Night Visions System
  Advanced system with front LEDs (illuminates intensely when driving forward), brake LEDs (illuminates intensively when braking), turn signals (flashing when turning to a specific side) and additional LEDs (for example for a light ramp). Possibility to connect another six light circuits.
• Light set -Standard - Axial set of LED lighting
  Standard light set with power supply module and diodes - The power supply module allows the connection of two LED beams, which will be permanently lit. The package contains high-brightness diodes ( 4x white LEDs for headlights and 2x red LEDs for taillights ).
• Axial control unit LED control unit, 3-port
  Control unit with the possibility of connecting three beams of permanently lit LED diodes. The package does not contain diodes - you can choose them according to your needs in the accessories for the item.

Accessories for normal operation

For normal operation of the Axial RC car, you need tire glue, bolt glue, a tool kit and silicone shock absorber oil. From our range we recommend an affordable set of tools for RC cars.

The tire glue adheres the tires to the rim of the disc. It is always necessary that the tire is firmly glued to the wheel rim around the entire circumference! If the tire is not stuck around the entire circumference, it may rupture. The tire adhesive has a special composition that is able to bond materials such as rubber or nylon, and at the same time the adhesive is flexible after hardening. We recommend Robitronic Tire Glue from our offer.

Sometimes it is necessary to add silicone oil to the model's shock absorbers and change the oil in the differentials. During normal operation, there is only a slight leakage of silicone oil along the shock absorber piston rods. If the damper piston rod surface or seal condition is in poor condition, the oil leak may be large. Repair kits or individual parts are supplied for these cases.

Screw glue is required for routine maintenance. Screws screwed into the metal material (eg screws in the motor, pin in the pinion) must be secured against loosening with this adhesive.

Protective covers for batteries

Protective covers are designed to reduce the risk associated with transporting and charging batteries. LiPo batteries can, while maintaining small dimensions and low weight, provide high discharge currents and have a large capacity for long travel times. On the contrary, the LiPo battery is particularly susceptible to mechanical damage.