Shopping Cart
There are no more items in your cart
Replacement "large" bowl for kitchen scale up to 13 kg SILVA 2 MAX
LiPo alarm 2-8S - audible voltage signaling
KAV38.0039
Kavan
Digital voltage meter for LiPo, LiFe, Li-ion batteries with 2-8 cells with adjustable low voltage sound signaling (2.70-3.80V) for 2-8S sets. Voltage measurement 4-15 V for NiXX battery at input (-) /
Express delivery
Large selection of carriers
Satisfaction guarantee
Recommended for you
Last items in stock
electronic
EB48 2.0 ET48 2.0 Tekno Buggy LapMonitor holder for transponder/personnel chip
Lapmonitor
MT10_EB48_ET48_ECO
electronic
LapMonitor holder for 1/10 touring car transponder/personnel chip
Lapmonitor
MT19_TOURING_CAR_SERVO
Last items in stock
Last items in stock
electronic
MP9 / MP10E LapMonitor holder for transponder / personnel chip
Lapmonitor
MT14_MP9_CARBON_ECO
Last items in stock
electronic
RC8B3e Team Associated LapMonitor Transponder/Personnel Chip Holder
Lapmonitor
MT08_RC8B3E
electronic
SRX8E SADDLE SERPENT LapMonitor holder for transponder / personnel chip
Lapmonitor
MT21_SRX8E_SADDLE
Replacement bowl for kitchen scale up to 13 kg SILVA 3
Last items in stock
LiPo alarm 2-8S is a miniature digital voltmeter with a three-digit LED seven-segment display capable of:
- measure and display the total voltage and voltage of individual cells in Li-Po, Li-ion and Li-Fe battery packs with 1-8 cells in series,
- acoustically and optically signal low voltage lithium battery cells with 2-8 cells in series with an adjustable threshold level for triggering an alarm of 2.70 to 3.80 V in steps of 0.10 V,
- measure and display the total battery voltage (NiCd, NiMH, Pb, etc.) in the range of 4.0-15.0 V
Voltage measurement of lithium batteries and cells
Just connect the service connector of the set to the LiPo alarm input and it will start working immediately. LiPo alarm can be used for sets with up to 8 cells in series. After connecting to the service connector of the LiPo set, the alarm first displays the detected number of cells of the set (eg reports three cells as "3CS", five cells "5CS" etc.), then displays the measured voltages of individual cells ("No.1"… voltage… "No. 2 "… voltage…) and finally the voltage of the whole set (" ALL "… voltage).
You can connect the LiPo alarm directly to the service connector if it is a system with a contact spacing of 2.54 mm and with terminals in the order of (-) sets, (+) Article 1, (+) Article 2 ... (+) 8 gapless link - ie JST-XH, JST-EH and PolyQuest systems (4S and more). An adapter must be used for PolyQuest (for 2 and 3S kits) and ThunderPower systems. LiPo alarm is compatible with adapters for RC System, Raytronic, Robbe, Graupner balancers.
Low voltage signaling
Connect the service connector of the 2-8 cell set (alarm does not work for single cell sets) in the same way as for voltage measurement. To set the threshold level for triggering an audible (2 really loud piezo sirens) and light (flashing red high-brightness LEDs located between the sirens and the display) alarm, press the SET button repeatedly in the range of 2.70 to 3.80 V in 0.10 V increments. < / p>
Measurement of total battery voltage
To measure the total voltage of NiCd, NiMH, Pb and other batteries with a voltage in the range of 4-15 V, connect the negative pole of the set to the (-) LiPo alarm input and the positive pole of the measured set to the 1S LiPo alarm input. The meter will indicate the total voltage as if it were a single-cell lithium battery.
The LiPo alarm 2-8S package contains: LiPo alarm 2-8S.
| Length [mm] | 40 |
| Width [mm] | 26 |
| Height [mm] | 11 |
| Weight [g] | 10 |
- Délka [mm]
- 40
- Hmotnost [g]
- 10
- Šířka [mm]
- 26
- Výška [mm]
- 11
11 Items
New
8596450030671
Customers who bought this product also bought:
Last items in stock
Extension cable of XT-30 connectors, cable cross-section 14AWG, length 12cm.
for servos installed in RC Cars
Smart module for 2S LiFe, LiPo, LiHv, ULiHv. Connection via battery balance connector. Miniature dimensions 36x16x9mm, weight only 2.8g. Controlled by BT via BattAir application.
Power connector with 6 mm gold-plated contacts with a load capacity of max. 100 A. For cables with a cross section of max. 8.4 mm2 (8AWG). Transition resistance 0.20 mOhm, max. 500 V. Pack of 3 pairs of contacts with housings in red, black and blue.
Two-pin power connector with flat gold-plated contacts with a load capacity of max. 50 A (long-term 25 A) with a rounded grooved body for a firmer grip and cable covers. For cables with a cross-section of max. 3.3 mm2 (12AWG). Transient resistance 0.45...
XT60 Female to Gold G4.0mm Female connector adapter. 1pc per package.
Pocket multifunctional voltage tester with LCD display for 1-8S LiPo, LiFe, Li-ion, LiHV, NiXX batteries, discharger/balancer for lithium batteries and servo tester with adjustable range of pulse width and repetition frequency.
Tap to zoom
