• -8.43 €
Obrázek
Obrázek

D980TW ultra strong digi servo (44kg)

1HI38806
Hitec
Monstrously powerful digi servo with new-generation titanium gears with electronics with lightning-fast response for demanding applications. Programmable, 4.8-7.4V power supply. Thrust 26kg.cm, speed 0.28s / 60 ° at 4.8V, thrust 44kg.cm, speed 0.17s / 60 ° at
More info
In stock - main warehouse: > 10 pcs
Original price
169.07 € -8.43 €
Your price with VAT
(DPH CZ 21%)
160.64 €
Price without VAT
132.76 €

  • Did you find a better price?
  • Did you find a better price?

    * Required fields

    We will reply as soon as possible, usually within a few hours.

    By submitting the form you agree to the processing of your personal data (read)

     

     

    Express delivery

     

    Large selection of carriers

     

    Satisfaction guarantee

     

    Hitec D Series Servos

    The new Hitec D series digital servos combine a responsive response, accuracy and high resolution 4096 steps in the HS-8xxx servo series with HS-7xxx servo programming capabilities. In fact, the existing servos are far superior to the 32-bit processor and 12-bit ADC converter. In addition, they offer a "Wide Voltage" feature that allows battery power to be used over a wide range of 4.8 to 7.4 V rated voltages.

    32bit MCU / 12bit ADC

    The new 32-bit Hitec processor coupled with a 12-bit analog-to-digital converter converting feedback signal potentiometer offers the best ever servo response for RC models. You can also use the versatile DPC-11 PC interface (applicable to all Hitec serviceable servos) to tune your D-Series servos to maximum performance (variance, resolution, fail-safe, soft start, etc.) in a wide range of applications.

    Wide Voltage

    Hitec Technology "Wide Voltage" supports all types of receiver batteries with a nominal voltage of 4.8-7.4 V. This means that the servos can be directly powered by eg from four to six cell NiMH or NiCd battery, LiFe, LiPo or Li-ion - Of course, it must be borne in mind that the servo pull and speed depend on the supply voltage.

    Twenty-five-tooth output shaft with 25 teeth

    The D-Series Servo Output Shaft has a standard 25-tooth (as standard, allowing for more accurate lever adjustment perpendicular to the servo's longitudinal axis), and new levers with a matching thousand-square (not compatible with older Hitec servos) are used.

    Soft start

    Soft start protects the servo and rudder control mechanism when switching on the on-board electronics - after switching on the servo moves slowly to the neutral position - there is no sudden jerk

    Smart

    New control algorithm to prevent the servo from spontaneously oscillating at "sharp" servo deadband settings, saving gears and reducing current draw.

    Programmable Features

    With the new DPC-11 programmer / USB interface, you can set a number of parameters for the D servo to fit your application perfectly. D Series Servos have consistently high resolution; with the help of the "deflection size (EPA)" function you can set the servo deflection range up to 180 ° (with control signal with pulses of 0.9-2.1 ms). Programmable values are:

    • reset to factory defaults
    • deadband bandwidth (adjustable in 10 steps)
    • sense of rotation
    • rotation speed
    • neutral
    • soft start
    • deflection size (up to 180 °)
    • on or off fail-safe
    • fail-safe emergency deflection adjustment
    • overload protection (overload limitation 0-50%)

    Splash Proof

    Servos are resistant to splashing water and moisture (not designed for permanent immersion in water). As a result, they are also suitable for use in harsh operating conditions in RC cars, boats and other models where the servos are exposed to the weather.

    D980TW

    A monstrously powerful titanium gear servo with output shaft mounted on two ball bearings for use in large RC models. Particularly suitable for giant aircraft models, racing RC cars 1: 5 and similar applications with extremely high pull force requirements.

    It will replace the HS-7980TH servos in the future.

    Servo size Standard
    Servo type digital
    Stroke at 4.8V [kg / cm] 26
    Stroke at 6.0V [kg / cm] 36
    Stroke at 7.4V [kg / cm] 44
    Speed at 4.8V [s / 60st.] 0.28
    Speed at 6.0V [s / 60st.] 0.21
    Speed at 7.4V [s / 60st.] 0.17
    Servo Transfers titanium
    Ball bearings 2xBB
    Highvoltage Yes
    Power Supply [V] 4.8 - 7.4
    Length [mm] 43.8
    Width [mm] 22.4
    Height [mm] 40
    Weight [g] 78.2
    Intended for airplanes, helicopters, road cars, off-road cars, sailboats, ships
    The number of teeth of a thousand square shaft 25
    Water Resistance splash-proof (p
    Obrázek
    Last items in stock
    Set of short levers and accessories for mounting servo series HS-8xxx and HS-9xxx with output shaft with thousand teeth with 25 teeth.
    levers

    Aluminum U servo lever, 25 teeth, 1 pc. 106mm

    Graupner/SJ
    7908.106
    Professional servo lever 25 teeth. Ready to use M3 ball studs. 25 tooth lever for Graupner, Hitec Dxxx/HS-8xxx/HSB-9xxx, Savöx and Futaba servos. Dimensions: Width 20mm, height 10mm, weight 10.8g, length 106mm
    Universal PC interface for software programmer and servotester for all Hitec programmable servos (classic and brushless). Allows you to set the amount of deviations, neutral, fail-safe, speed, direction of rotation, deadband, soft start and resolution
    Flat extension cable with JR connectors 100 mm long with PVC insulation, conductor cross-section 0.25 mm2. The socket (counterpart) is equipped with a snap-on safety device to ensure the connection of the connectors.
    Obrázek
    • Special price
    Flat

    Extension cable 15cm JR (PVC)

    Kavan
    KAV36.2212
    Flat extension cable with JR connectors 150 mm long with PVC insulation, conductor cross-section 0.25 mm2.
    Flat extension cable with JR connectors 150 mm long with PVC insulation, conductor cross-section 0.25 mm2. The socket (counterpart) is equipped with a snap-on safety device to ensure the connection of the connectors.
    Flat

    Extension cable 30cm JR (PVC)

    Kavan
    KAV36.2213
    Flat extension cable with JR connectors 300 mm long with PVC insulation, conductor cross-section 0.25 mm2.
    Flat extension cable with JR connectors 300 mm long with PVC insulation, conductor cross-section 0.25 mm2. The socket (counterpart) is equipped with a snap-on safety device to ensure the connection of
    Flat

    Extension cable 60cm JR (PVC)

    Kavan
    KAV36.2214
    Flat extension cable with JR connectors 600 mm long with PVC insulation, conductor cross-section 0.25 mm2.
    Flat extension cable with JR connectors 600 mm long with PVC insulation, conductor cross-section 0.25 mm2. The socket (counterpart) is equipped with a snap-on safety device to ensure the connection of
    Flat extension cable with JR connectors, length 750 mm with PVC insulation, conductor cross-section 0.33mm2 / 22AWG. The socket (counterpart) is equipped with a snap-in fuse to secure the connection of the connectors.
    Flat

    Extension cable 90cm JR (PVC)

    Kavan
    KAV36.2215
    Flat extension cable with JR connectors 900 mm long with PVC insulation, conductor cross-section 0.33 mm2 / 22AWG.
    Flat extension cable with JR connectors 900 mm long with PVC insulation, conductor cross-section 0.25 mm2. The socket (counterpart) is equipped with a snap-on safety device to ensure the connection of
    Twisted strong extension cable with JR connectors, length 600 mm with PVC insulation, conductor cross-section 0.25 mm2. The socket (counterpart) is equipped with a snap-in fuse to secure the connection of the connectors.
    electronic

    HFP-30 Hitec digi servo programmer

    Hitec
    1HI3306
    HITEC digital servo programmer (all series) and servo tester. For programming HITEC digital servos of the HS-5xxx, HS-7xxx, HSB-9xxx, Dxxx series and testing all types of servos (digital and analog). Possibility of synchronous programming of two...
    Obrázek
    Last items in stock
    Other

    Servo holder

    PELIKAN
    2DH0094-2
    Standard size servo bracket
    Obrázek Obrázek 2
    Last items in stock
    levers

    Servo lever 25mm (1 ") 25 teeth M3

    Kavan
    KAV20.3702
    Professional servo lever for servos with 25-tooth output thousand (Hitec Dxxx / HS-8xxx / HSB-9xxx, Savöx and Futaba). Made of aluminum with M3 threads for the use of ball joints. Distance of the hole from the servo axis: 25mm.
    levers

    Servo lever 38mm (1.5 ") 25 teeth M3

    Kavan
    KAV20.3704
    Professional servo lever for servos with 25-tooth output thousand (Hitec Dxxx / HS-8xxx / HSB-9xxx, Savöx and Futaba). Made of aluminum with M3 threads for the use of ball joints. Distance of holes from the servo axis: 38mm; 32mm.
    levers

    Servo lever 45mm (1.75 ") 25 teeth M3

    Kavan
    KAV20.3705
    Professional servo lever for servos with 25-tooth output thousand (Hitec Dxxx / HS-8xxx / HSB-9xxx, Savöx and Futaba). Made of aluminum with M3 threads for the use of ball joints. Distance of holes from the servo axis: 45mm; 38mm; 32mm.
    levers

    Servo lever 51mm (2 ") 25 teeth M3

    Kavan
    KAV20.3706
    Professional servo lever for servos with 25-tooth output thousand (Hitec Dxxx / HS-8xxx / HSB-9xxx, Savöx and Futaba). Made of aluminum with M3 threads for the use of ball joints. Distance of holes from the servo axis: 36mm; 42.5mm; 51mm.
    Double arm universal carbon lever for servos 110x22 mm, center hole 8 mm. For screwing onto standard plastic servo discs.
    Double arm universal carbon lever for servos 60x22.5 mm, center hole 7 mm. For screwing onto standard plastic servo discs.
    levers

    Servo lever carbon single arm 40x21mm

    Kavan
    KAV20.3914
    Single-arm universal carbon lever for servos 40x21 mm, center hole 9 mm. For screwing onto standard plastic servo discs.
    Single arm universal arc carbon lever for servos 53x20mm, center hole 9mm. For screwing onto standard plastic servo discs.
    Obrázek
    Last items in stock
    Double arm universal arc carbon lever for servos 110x31 mm, center hole 9 mm. For screwing onto standard plastic servo discs.
    Professional double-sided servo lever with offset for servos with 25-tooth output hexagon (Hitec Dxxx / HS-8xxx / HSB-9xxx, Savöx and Futaba). Made of aluminum with M3 threads for the use of ball joints. Hole spacing: 114mm; 102mm; 89mm; 76.5mm; 63.5mm
    Professional double-sided servo lever for servos with 25-tooth output thousand (Hitec Dxxx / HS-8xxx / HSB-9xxx, Savöx and Futaba). Made of aluminum with M3 threads for the use of ball joints. Hole spacing: 64mm; 50mm; 38mm.
    Professional double-sided servo lever for servos with 25-tooth output thousand (Hitec Dxxx / HS-8xxx / HSB-9xxx, Savöx and Futaba). Made of aluminum with M3 threads for the use of ball joints. Hole spacing: 89mm; 76.5mm; 63.5mm.
    Other

    Servo Washers (8pcs)

    PELIKAN
    2DH0066
    High quality aluminum washers for servo mounting.
    Twisted strong extension cable with JR connectors 300 mm long with PVC insulation, conductor cross-section 0.25 mm2. The socket (counterpart) is equipped with a snap-on safety device to ensure the con
    Twisted strong extension cable with JR connectors, length 900 mm with PVC insulation, conductor cross-section 0.25 mm2. The socket (counterpart) is equipped with a snap-in fuse to secure the connection of the connectors.
    5387 Titanium gears D980TW
    • -2.25 €
    Last items in stock
    transfers

    5387 Titanium gears D980TW

    Hitec
    1HI6425

    Customers who bought this product also bought: