Express delivery
Large selection of carriers
Satisfaction guarantee
VIBE is a high-performance two-plane 3D aerobatic special of the park-fly category made of EPP foam designed to be driven by AC electric motors with a power of 350-500 W. A few hours with instant glue in hand is enough to complete this model capable of flying the turns of the classic F3A assembly, as well as hanging on the propeller and perform all other 3D stunts! It is also intended for less experienced pilots; with minor deviations, it can be flown by anyone who already has at least some experience with acrobatics and is able to reliably fly flips, headwinds and twists with the previous model. Due to the light weight of the model, a possible crash due to "hand entanglement" does not hurt too much - and the EPP parts are so easy to repair!
One-piece wings with large winglets have a symmetrical profile, strength is provided by carbon beams, and in the lower wing, of course, there are prepared shafts for servos. The upper wing canopy strut reinforced with plywood parts is part of the fuselage, the mid-wing struts are made of carbon-reinforced EPP. The fuselage is profiled with a horizontal part thoroughly reinforced with carbon flanges and a vertical part with a large side surface for perfect behavior in knife flight. The well-thought-out design includes a plywood engine bed anchored to the hull using carbon flanges. Elevator and rudder servo shafts are prepared in the fuselage. The tail surfaces are also carbon-reinforced EPP. The ailerons, rudder and elevator are controlled by short straight carbon or steel rods. The main chassis is carbon with two lightweight wheels and EPP covers; it is fixed with 2 screws to the supporting laminate board anchored to the hull with laminate holders. A spur with a 3D printed console and a light foam wheel is coupled with the turn signal.
To control the model, you will need at least a four-channel RC kit, which should at least have the ability to set double and exponential deflections.
For undemanding recreational flying, ordinary analog microservos with metal gears such as KAVAN GO-13MG, Hitec HS-65MG, etc. are suitable. If you are serious about acrobatics, you should use strong and fast digital servos with metal gears, such as KAVAN GO-1013MG, Hitec HS-5065MG etc.
For propulsion, we recommend a KAVAN PRO 3536-1000 AC electric motor, Model Motors AXI 2814/16 V2 or similar with an APC 11x4.7SF propeller when powered from a 3S LiPo battery or 10x4.7SF when using a 4S LiPo.
The speed controller should have a load capacity of at least 40A, and especially if you use strong and fast digital servos, it should have a powerful switching BEC power stabilizer, such as the KAVAN PRO-40SB or KAVAN R-50SB Plus.
A three- or four-cell LiPo battery 1300-1800 mAh with a load capacity of at least 40C is suitable for power supply.
VIBE was designed and manufactured in the Czech Republic.
The kit includes: printed parts of the fuselage, wings, tail surfaces and chassis covers cut from EPP foam, plywood engine bed, 3D printed plastic parts, carbon struts, levers, forks, tie rods and other small accessories, carbon chassis with light wheels, detailed picture instructions to construction.
Notice
According to Commission Delegated Regulation (EU) 2019/945 of March 12, 2019 on unmanned systems and third-country operators of unmanned systems and Commission Implementing Regulation (EU) 2019/947 of May 24, 2019 on rules and procedures for the operation unmanned aircraft operators and pilots of unmanned flying devices (classic aircraft models, multicopters, drones) that weigh more than 250 g or carry a camera or other sensor capable of capturing personal data in any way are required to register (in the Czech Republic with the Civil Aviation Authority) . More information can be found here: Drone registration
| Span [mm] | 1000 |
| Length [mm] | 1030 |
| Weight [g] | 750 - 800 |
| Controlled functions | S,V,K(2),M |
| Difficulty of construction | S2 |
| Difficulty of piloting | P2, P3 |
