ROBIN II 1875mm Kit

ROBIN new at first glance fit between our very successful and popular models ALPHA GAMMA 1500 and 2100. Like the two older sisters has a thorough design of the foam EPP cleverly paved carbon reinforcements. A two-piece wing and tail surfaces screwdriving easily removed. ROBIN because the school provides an excellent model for beginners that is easily "readable" in the air is stable and has excellent lubricity. Likewise, it is a great pleasure ROBIN model model for a relaxing flying, pilots of all ages and levels of experience.

Preserved remains of course the proven advantages of Alpha Gama: wing with a large bearing surface, controlled by the ailerons, rudder and elevator, a powerful AC motor drive. Robust - and yet very lightweight - construction of expanded EPP with carbon struts ensures excellent resistance to damage during a crash or at least very ease of repair if any damage already occurs. To control you basically just even the most ordinary four-channel RC set. Ensure normal supply Li-Po tříčlánek 1300-1800 mAh - again no challenge, it has today everyone!

ROBIN is a powerful motor glider from durable extruded polypropylene EPP driven by an AC motor. The hull is molded from a foamed EPP and is ready for mounting an AC motor with a rotary casing (class C2830 1300 rpm to V) on a glued plastic motor mount. In the cabin are prepared shaft servo rudder and elevator corresponding directly with little or modifying the conventional 9-12 g servos. Canopy is removable magnetic closures. For the recommended motor is suitable for folding propeller 9.5 "if you do not taper provided in the kit, you will need a 45 mm cone. Cooling the engine controller and the battery assist cooling air inlets on the sides of the bow necessary outlet for heated air is to the bottom of the hull in the area beneath the wing. < / P>

Two-piece wing with the proven "soaring" profile is also molded from EPP for aileron control short straight wire rods are prepared pits corresponding directly with little or modifying the conventional 9-12 g servos. Wing combine carbon pipe clamps; release halves of the wings during flight prevents the locking screws on the underside of the wing.

Empennage in conventional arrangement are made from EPP, they are controlled by means of wire rope pull. The trunk was fixed with screws so that they are easily removable for transport and storage.

To control the model you need at least four channel radio system (if you are happy with the controls aileron servos connected to the Y-cable), but to take full advantage of the model is suitable to use at least a five-channel computer radio system enabling to connect and adjust each servo individually. Note .: construction model enables simple enough to add two additional servo flaps control - but in this case it is necessary to use a controller with powerful switching BEC power stabilizer necessary for 6 servo or BEC in the current controller and exclude receiver and servos powered by an additional stabilizer switched UBEC with continuous load capacity of at least 3 A.

To control the rudders can use quality 9-12 g servos (HS-55, HS-53, HS-65HB, 09 GO-GO-13MG etc.). Especially if you intend to fly the model on the slopes or indulge divočejšímu style, we recommend using a stronger servos, respectively. with metal gears.

For power you need Robina Li-poly battery 11,1 V with a capacity of at least 1300 mAh. Model "can carry" tříčlánky until about 1800 mAh.

ROBIN is for beginners - as always deliver - under the supervision of an experienced pilot, as well as for anyone who wants just as nice recreational flying. The flight characteristics are good, straightforward and accurate control of the model. The model will acquaint you with full governance model around all three axes; coordinated with the proper control rudder, ailerons and elevator. This experience was "like finding" no later than immediately after embarking on his first flying aerobatic model glider or even more. Even if you do not have a computer radio system, changing the ratio of the lengths of servo and rudder can adjust the size of variations in the large range. Beginner starts with small, safe and excessive "steering"; experienced pilot will set up a large, allowing a little bit the rudimentary motor-větroňové stunts - flips, barrel rolls, Wing over Robin go with a little help from the engine very easy and good! Engine power is adequate for continuing to climb at an angle of 30-40 °, thus ascending to a height sufficient for catching thermals will not be long! ROBIN sensitive even to weak thermals, easily the precise control along all axes and settles into a rising stack of small diameter.

Rychlostavebnice contains: fuselage, wing and tail molded EPP, spinner, carbon tube coupling wings and detailed instructions for building and flying.

NOTE: We apologize for printing error that has crept into the manual - kit contains a plastic cone, NOT propeller, as stated in the manual by mistake.

Recommended drive and RC equipment: