214264 Solius 2160mm glider / electric

Since its first performance at the Nuremberg Toy Fair has been less than a month, yet the snow melted, and now you can start the construction of gliders latest ELAPORu from Multiplex! Let's take a look at what our "German comrades" prepared. You will see that again overcome, and offer us even smarter, more sophisticated, and as always great flying model! Simply, "White even whiter!" in the best modeling design!

Solius builds on the proven aerodynamic concept Easy Glider, which adds to the elegance of modern gliders in 's-es-wéčkovém "style. At first glance slender hull with a transparent canopy with marked cockpit, tail in delight T arrangement enabling easy removal of the horizontal tail for transport. Wing with a wingspan of 2160 mm retains the thinness, thanks to a reasonable large bearing surface and thus guarantees excellent strength properties and good behavior at low speeds.

The fuselage is made of almost indestructible foam ELAPORu. The secret that allows you to have foam hull and slender, thin-walled tube is hexagonal aluminum alloy reinforcing fuselage from the wing on the tail. Pipe appreciate even during model building - Now You might be able to build a torso twisted just really exerting too much effort! Tube are also listed extension cords servo rudder and elevator. The prow of the fuselage and the tail further strengthens several fiberglass rods vlepovaných between the torso and the tail fin. The engine is mounted in the nose of plastic motor mount with a universal pre- drilled holes and grooves for mounting screws - they should satisfy the vast majority of conventional AC motors adequate performance. Included in the kit is a spinner with grippers with collet for engines with 5 mm shaft and propeller blades 12x6 ". If you decide to use a motor with a 4 mm shaft, purchase the appropriate spinner # 73 Multiplex Multiplex 3500. The designers have not forgotten the hull provide intake and exhaust vents provide cooling motor, controller and flight battery. The model can also complete a "clean" glider - in the case is in the kit comes molded bow of ELAPORu ready for installation hook for aero tow. Canopy with transparent "bubble" is removable, fixed with a pair of conventional plastic locks Multiplex. The bow will find ample space for controller, drive battery and receiver. Servo rudder and elevator are stored in kýlovce, rudder control short straight wire rods.

Wing model foamed ELAPORu is separate beams of rectangular tube of aluminum alloy whose protruding part serves as a coupling wings. Wing is secured in place sophisticated pin fitting into a lock on the root ribs - the pin is removed and retracts from the cabin. For the aileron servos are ready to pit with plastic covers, wings (along reinforced thin-walled tube of stainless steel) are controlled independently by two short straight wire rods.

The tail surfaces are also made of foam ELAPORU with reinforcements from fiberglass rods. Horizontal tail attaches to the top of the fin using two screws polyamide.

Wheeled landing gear is in "ASW" style, with the main round with a diameter of 45 mm and a sliding shoe on the tail.

To drive the model, you'll need a brushless motor AXI classes from 2814 to 2820 with a 40-50 A regulator, preferably with switching BEC power stabilizer to ensure a reliable power supply on-board electronics.

To serve the power Li-poly tříčlánek with a capacity of 2200 mAh or more capable of carrying at least 20C. Specific type select so that you without further adding of the most relied correct center of gravity.

To control model basically make do with even the most ordinary four-channel radio system, so you can use the on-board equipment as well as from your "olétaného" beginner RC set. The ideal, of course, use at least a five- or six-channel computer RC system enabling independent control of two mA aileron servos and their role in mixing the air brakes (both ailerons deflect up consistently). Ready to match pits servos HS-55 / HS-5055MG (Nano-S) for the rudder and elevator and HS-81 / HS-82mg (Tiny-S) for the wings. Especially if you choose the drive system at AXI 2820, and you will want to fly more dynamically and on the slope, we recommend installing more powerful servo with metal gears.

Kit includes: moldings fuselage, wing and tail made of foam ELAPORu, transparent canopy, hexagonal tube of aluminum alloy and other reinforcements from fiberglass and stainless steel set of small parts and accessories, landing gear 45mm, folding propeller with a 55 mm cone with grippers with 5 mm collet and leaves 12x6 ", two sheets of stickers and instructions.

Drive and RC equipment: