1-00912 TwinStar BL-ND 1420mm - kit

Twin-engine high-altitude aircraft with acrobatic capabilities for 2 AC motors of the AXI2212 class in a new color design ND. Quick kit in bulk with parts made of highly durable ELAPOR, controlled ailerons, rudder, elevator. Ideal as the first twin-engine mode

MPX100912

New product

Multiplex

Sale ended

More info

Recommended accessories

More info

The two-engine model with acrobatic capabilities from ELAPOR for two-phase ACI 2812 AC motors is a follow-up to the proven and very popular "DC" predecessor TwinStar II. In contrast, it has a new engine bed with a metal motor bulkhead, properly sized for today's powerful AC motors. TwinStar BL is perfectly suited as the first twin-engine model for recreational pilots. It can easily do basic acrobatics and thanks to its low area load, launches from the hand and landing on the belly are very easy. And of course, plenty of brushless power allows the floats to float all summer!

The fuselage of the model consists of moldings of foam Elapor, as additional reinforcements of the tail part is the tube of the cable and antenna tube. In the bow under the removable cabin cover there is space for the propulsion battery and rudder and elevator servos. In the space under the wing you will find enough space for two speed regulators and a receiver. Cooling of the propulsion accumulator and regulators is provided by an air duct with a suction port on the top of the bow and an outlet behind the wing.

The two-piece wing made of foam Elapor connected by a composite pipe coupling is fixed to the fuselage by two polyamide screws with plastic clips. The motors are mounted on metal motor bulkheads bolted to a plastic bed glued to the engine nacelles - so you can easily replace the motors at any time. Aileron servos are mounted in prepared shafts in both halves of the wing; the wings are controlled by short straight wire rods.

The tail surfaces are also from Elapor, rudders are controlled by cableways.

To control the model you will need at least a four-channel RC set, of course, ideally is at least a 5- or 6-channel computer RC set with the possibility of adjusting the magnitude of deflections and exponentials. In the fuselage and wing are prepared servo shafts corresponding to Hitec HS-81 or HS-82MG servos, respectively. MULTIPLEX Tiny-S

You will need two AXI 2212 AC motors with 1100-1300 rpm on V to drive - remember that TwinStar BL allows you to mount a maximum of 8 ”propellers. 20-25A AC controllers will work well for a given motor.

Use a three-cell LiPo battery 3000-3700 mAh with a load capacity of at least 30C.

The TwinStar BL can be easily retrained on a seaplane with the # 73 3061 float set, and with functional lights # MULTILight Power # 73030.

The kit contains: moldings of the fuselage, wings and tails of Elapor, rods, levers and other small accessories, plastic motor beds with metal motor bulkheads, sheet of pre-cut stickers and construction instructions.

Span [mm] 1420
Length [mm] 1085
Weight [g] 1350 - 1500
Wing area [dm 2 ] 43
Controlled functions S, V, K (1), M (1)
Construction demands S1
Difficulty of piloting P2

Recommended drive and RC equipment:

MPX Power Set Eco RAY Sport FOXY Sport AXI
Engine * 2x Permax BL-O 2830-1100 2x RAY G2 C2830-1300 2x FOXY G2 C2212-1100 AXI 2212/20
Regulator * 2x MULTIcont BL-20SD 2x RAY R-20B 2x FOXY R-25B 2x FOXY R-25B
Power accumulator RAY G4 11.1 V 3250 mAh RAY G4 11.1 V 3250 mAh RAY G4 11.1 V 3250 mAh RAY G4 11.1 V 3250 mAh
Propeller * 2x 8x5 “ APC 8x4,7SF APC 8x6SF APC 8x6SF
Servos 4x HS-81 4x GO-17MG 4x HS-81 4x HS-81
RC set min. 4 channels min. 4 channels min. 4 channels min. 4 channels
*) Part of Power Set # 33 2619

Recommended accessories