Arrma Senton 3S BLX 1:10 4WD RTR blue

Reinforced chassis

Several changes in reinforcement were made on the chassis, for greater rigidity. At the same time, aluminum was used on the axle pin retaining plates. The chassis design is arranged in a proven component layout to achieve a perfect balance. Drive shaft in the middle, battery on one side and electronics on the other. In addition, the entire chassis is equipped with side covers that limit the ingress of dirt into the chassis. The battery is firmly seated in place with straps.

Larger handle on the drive module

The area of the "Pull" board has been increased for better mounting and handling of the drive module.

Pinion with driven gear

The motor can be adjusted and the inter-tooth clearance precisely adjusted when replacing the pastor or gear, thanks to the aluminum plate with grooves for mounting the motor.

Ball bearings

All rotating parts are mounted in ball bearings. Exposed bearings are protected against dust and dirt by rubber caps.

Servo saver for servo protection

The model received a new more powerful servo saver and a new more efficient servo saver was used for its maximum protection. This provides a higher level of impact protection and safer driving.

Grooved shafts

As with the 4S version, grooved shafts are used here, which can easily transmit the high power of the AC motor. / p>

Wheels and tires

Robust, multi-spoke discs with dBoots® Fortress-SC tires with a distinctive pattern, give the RC model car Senton 3S BLX Short Course Truck maximum grip on all surfaces.

Oil dampers

Patented oil dampers absorb every impact of the model. The shock absorbers are equipped with impact protection covers on the front. The change in stiffness and ground clearance is possible with the aid of oil viscosity or spacers. silicone O-rings are used for safe oil retention.

Compact chassis

The chassis design is arranged in a proven component layout to achieve a perfect balance. Drive shaft in the middle, battery on one side and electronics on the other. In addition, the entire chassis is equipped with side covers that limit the ingress of dirt into the chassis. The battery is firmly seated in place with straps.

Front and rear differential

The model is equipped with front and rear differentials, which ensure maximum traction. The differentials are equipped with high-quality metal gears for trouble-free operation. The wheel drive is transmitted by means of telescopic half-axles.

Flexible bumper

The front of the Senton 3S BLX protects against impact from a flexible frame bumper that is mounted at four points. In case of damage, the bumper can be easily replaced.

Proven AC drive

The drive unit consists of a Firma 3660 AC motor and a BLX100 AC controller. Each of these units forms a separate modular system.

Easily accessible engine module

The engine module is removed from the chassis as a complete unit, removing one bolt. Includes engine, engine plate, clutch assembly and transmission cover.

Easy disassembly of the electronics module

The electronics module consists of a waterproof receiver box, servo board and controller holder. The unit is dismantled and is available for maintenance and service needs.

Front and rear differential

The model is equipped with front and rear differentials, which ensure maximum traction. The differentials are equipped with high-quality metal gears for trouble-free operation. The wheel drive is transmitted by means of telescopic half-axles.

Fixed shock absorber towers

The pins at the ends of the shock absorbers are fixed in the shock absorber towers on both sides, therefore they do not twist and a stronger fastening of the shock absorbers is guaranteed.

Digital Servo Control Spectrum MS SPMS651 MG

New Servo for Directional Control The Spektrum S651 7kg MG MG has 15% more torque than the previous ADS-7M servo. It is waterproof, has metal gears and a torque of 7.27 kg.cm at 6V.

BLX 3660 AC motor

The model is powered by a powerful 4-pole AC motor BLX 3660 3200 rpm // V. The four-pole design gives the motor a linear course from low speeds. The metal black anodized case not only looks amazing, but also allows better heat dissipation to the passive cooler. 4 mm pin connectors allow easy disconnection for easy engine maintenance.

• Power supply up to 3S LiPol
• Very smooth operation thanks to the 4-pole design
• Gold-plated connectors for perfect current transfer
• Shaft O 5mm

BLX100 electronic controller

The BLX100 AC regulator with a current load of up to 100A, in combination with 3S LiPo batteries will provide incredible power. The built-in fan ensures sufficient cooling even at full load. The controller has driving modes, protection against battery undercharge and overvoltage protection. Voltage BEC 6V. Waterproof * switch on the controller. Battery connector IC5.

Adjustable parameters:

• Switching voltage: NiMH / LiPo
• Acceleration: in 7 steps. Tip: On slippery surfaces, it is better to use less acceleration to prevent the wheels from slipping
• Brake forces: 25%, 37.5%, 50%, 62.5%, 75%, 87.5% and 100%
• Mode: Forward / brake / reverse or forward / brake
• Direction of motor rotation: Normal or reverse

New IC5 connectors

The new IC5 connectors have a modern design with an emphasis on safety and simplicity. The contacts are made of gold-plated pins and sockets with a diameter of 5 mm.

As already mentioned, the connectors have been designed with an emphasis on safe and easy use. The connectors cannot be reversed in polarity, the contacts and soldered connections are covered with a plastic cover. The IC5 connector is backward compatible with EC5.

Transmitter Spectrum SLT3

The basic 3-channel Spektrum SLT3 steering wheel operating at 2.4 GHz is compatible with the SLT protocol. The low weight of the Spektrum SLT3 transmitter allows for fatigue-free holding. The steering wheel is covered with a foam rim for a firm grip. The layout of the controls is practical and intuitive - all controls are positioned so that they are quickly accessible when needed. A secure loop is available for attachment to the strap.

• 3-channel steering wheel RC set Spektrum SLT for reliable control
• Proven design for comfortable grip without fatigue
• Possibilities of limiting the maximum deviations of the control channel and gas
• Dual steering channel deflections and 50%, 75% and 100% engine power limiter
• You can use the third channel for additional devices, eg for sound modules.

SLR300 receiver with SLT-FHSS protocol

The car 3-channel receiver SLR300 is equipped with SLT FHSS 2.4GHz technology, resistant to interference. It is compatible with Spektrum SLT transmitters and is backward compatible with Tactic steering wheel transmitters.

Recommended LiPo batteries

The model can be operated on a 2 to 3 cell LiPo battery or a 7 cell NiMH battery. The battery should be equipped with an EC5 or IC5 connector. For normal riding, we recommend a 2-cell LiPo battery (7.4 V).

• For normal riding LiPo battery Spectrum 7.4 V 5000 mAh with Smart technology.
• For the maximum possible speed of LiPo battery Black Magic LiPo 11.1 V 5000 mAh.
• For the maximum possible speed of LiPo battery Spectrum LiPo 11.1 V 5000 mAh with Smart technology.

Spektrum batteries with Smart technology are currently the most modern and safest way to maintain and charge batteries. You can find the advantages of Spektrum Smart technology here.

Recommended NiMH batteries

NiMH batteries are not demanding on precise handling and are therefore suitable if the RC model of the car is operated by children (NiMH batteries are not destroyed by complete discharge). However, NiMH batteries have a lower capacity, so driving time will be slightly shorter.

Recommended chargers for conventional and Smart batteries

If you decide to use modern Smart LiPo batteries in the RC model of the Arrma car, then we recommend this charger:

• Charger with mains power supply Spektrum S150 with one 1x50W output.
• Mains charger Spektrum S1100 with one 1x100W output.
• Mains charger Spektrum S2100 with two outputs 2x 100 W. <

To connect the battery to these chargers, you need an IC5 / IC3 charging adapter.

• High-performance mains charger Spektrum Smart G2 charger S1400 1x400W AC with one 400W output.
• High-performance mains charger Spektrum Smart G2 charger S2200 2x200W AC with two 2x200W outputs.

Accessories for normal operation

For normal operation of an RC car, you need tire glue, screw glue, a set of tools and silicone oil for the shock absorbers. From our range we recommend an affordable set of tools for RC cars.

The tire glue adheres the tires to the rim of the disc. It is always necessary for the tire to be firmly glued to the wheel rim around the entire circumference! If the tire is not stuck around the entire circumference, it may rupture. The tire adhesive has a special composition that is able to bond materials such as rubber or nylon, and at the same time, after hardening, the adhesive is flexible. We recommend Robitronic Tire Glue from our offer - see recommended accessories.

Occasionally it is necessary to add silicone oil to the model's shock absorbers and change the oil in the differentials. During normal operation, there is only a slight leakage of silicone oil along the shock absorber piston rods. If the surface of the shock absorber piston rods or the condition of the seals is in poor condition, the oil leakage can be large. For these cases, repair kits or individual parts are supplied. From our offer of silicone oils, we recommend silicone oils TLR (Team Losi Racing), see recommended accessories.

Screw adhesive is required for routine maintenance. Screws screwed into the metal material (eg screws in the motor, set screw in the pinion) must be secured against loosening with this adhesive.

Protective covers for batteries

Protective covers are designed to reduce the risk associated with transporting and charging batteries. LiPo batteries can, while maintaining small dimensions and low weight, provide high discharge currents and have a large capacity for long travel times. On the contrary, the LiPo battery is prone mainly to mechanical damage.