264285 EXTRA 300 S ARF set"

ARF set of an aerobatic aircraft (span 1200 mm) from ELAPOR with installed BL3720-630 AC motor, 50A controller and 4 servos. The model with a very precision sophisticated construction, controlled aile

1M401072

New product

Multiplex

2 pcs

Detail skladů
  • Skladem na prodejně Praha 9: Monzítří from 14:00
  • Skladem na prodejně Praha 5: 1 pcs
Další možnosti a termíny
In store: 1 pcs
Prodejny a termíny doručení
Cena s DPH:
223,54 € 212,38 €
Cena bez DPH:
175,52 €

-11,16 €

B B

More info

Video

Náhradní díly

Doporučené příslušenství

More info

EXTRA 300S, the latest of acrobatic electro ELAPORu from Multiplex confirmed the tendency towards maketám. After Tucano is now ready to begin acrobatic special, which is designed primarily with respect to the classic flying acrobatics, but can also hang well on the propeller turns in 3D. He would not even MULTIPLEX had brought "White even whiter!" in the best modeling design!

At first glance you attract clean design with recessed hinges maketovými rudder - you do not overcome the resistance of the foam rudder to move freely and smoothly throughout the 3D big screen. The chassis is bolted to sturdy plywood board recessed into the hull, all the parts fit together perfectly and the finish is elegant and flawless ... In addition, the model is almost entirely finished, with fitted motor, controller and servos!

The fuselage is made of foam ELAPORu with "multiplexácky" sophisticated internal construction provides a model at low weight necessary strength, easy access to the engine and electronics and zajiš'tující good cooling motor, controller and flight battery. Brushless motor Permax BL-O 3720-0630 driving a three-blade propeller 12x8 "with precision plastic cone is mounted at the rear mounted on a plywood partition. The cowl mounted two magnets on the sides is easily removable and provides access to the engine and 50 A controller MultiCONT BL50. On top of the fuselage before the cabin is removable battery compartment cover and receiver (again on hold magnets). Transparent canopy cockpit indicated the seat and the dashboard is fixed. Servo rudder and elevator are located in the tail and rudder control short straight rods.

Two-piece wing is symmetrical profile is made of foam ELAPORu; half are connected using carbon tube and attach screws to the fuselage. Aileron servos are installed; Wings are again dominated by short wire rods.

The tail surfaces are also made ELAPORu, the trunk was fixed with plastic pins and screws.

Landing gear is a solid two-wheeled chassis with dural legs and manageable spur coupled with the rudder.

Finishing the model is already completely finished with color spray and stickers.

To supply power unit model, you'll need a four LiPo battery with a capacity of 2600-2700 mAH and a load capacity of at least 25 C, for 3D aerobatics at least 35C.

To control model with fixed undercarriage basically just the normal four-channel radio system, to exploit all of the model is optimal to use at least a six-channel computer radio system.

The regulator MultiCONT BL50 is set and programmed in the same way as our regulators RAY series and can be used programming card for regulators RAY.

The kit contains: assembled fuselage with installed motor, controller and two servos, servos are mounted directly in the wings, tail surfaces of ELAPORu, three-blade propeller with a plastic cone, a hard duralumin chassis with wheels and aerodynamic covers, a carbon tube coupling wings, a set of small accessories and instructions.

Margin [mm] 1200
Length [mm] 1086
Weight [g] 1450
Wing area [dm 2] 37.23
controlled functions S, V, K (2), M
Building intensity S1
Difficulty piloting P2, P3

Drive and RC equipment:

MPX acro MPX 3D
Engine * Permax BL-O 3720-0630
Regulator * MultiCONT BL50
Propeller * 12x8 "
battery RAY G3 14.8 V 2700 mAh FOXY G2 14.8 V 2600 mAh
Serva * 4x MS-13020
RC rig min. 4 channels, but rather at least 5 channels Computer
*) Part of ARF set

Video

Náhradní díly

Doporučené příslušenství