CADET 4 (Protocol V3) 2.4 GHz mode 1"

4 Channel 2.4 GHz FHSS with Crossfire Controllers"


New product


Prodej skončil

More info

Doporučené příslušenství

More info

A modernized version of the classic four-channel RC system 2.4GHz FHSS (Frequency Hopping system spread-spectrum) - transmitter with two universal remote control, mechanical trims, switches sense deviations for each channel, and switchable mixer for flying wing and V-tail. It is intended for recreational hobbyists of all skill - good matches for simple models of airplanes, cars and ships and is smart enough even for "unbreakable" helicopter FunCopter from Multiplex, and flying wing models with "Véčkovým" tail. CADET 4 V3 is ideal for beginners who want to invest "a fortune" to the hobby in which only rozkoukávají for trips with folding model and a small backpack, traveling on vacation ...

What is at RC rigs CADET 4 V3 new?

Above all, it is a new VF episode using the new transport protocol v3, which provides greater reach RC rigs (800 m on the ground) at a low current consumption. On the transmitter switches besides the usual sense of the servos are also switchable mix for V-tail and flying wing (Delta). For power now make do with four AA alkaline batteries or NiMH batteries, which due to a lower sampling transmitter lasts longer.

To put the transmitter into operation will need 4 AA (AA) batteries which can be charged without removing the transmitter via built-in charging connector. For charging, you can use the compact AC charger Hitec CG-S32 or other suitable charger - a constant current source with a charging cable Hitec # 6375th

Receiver RX-600 V3 is smaller and lighter than earlier versions and allows you to set up emergency deflection fail-safe in case of strong interference or complete loss of signal from the transmitter.

Set with a six-channel RX-600 V3 mass and radius (800 m on the ground) is suitable for Slow and park-flyers, conventional electric motor and gliders. < / P>

ATTENTION: The transmitter CADET 4 V3 is not compatible with 2.4GHz receivers with two antennas (Protocol V1 and V2) previously supplied in RC sets Pelikan Daniel (Alpha 1500 Skylady III 2.4GHz, 2.4GHz Cessna 480, BETA 1400 Pioneer, ASW-17 , FOX-1800, Baby Warbirds etc.), or sold separately. Likewise, the new RX-600 V3 (single antenna) are not compatible with older transmitters embodiments CADET Protocol (V1 and V2). Procedures of pairing is also different.

The kit includes:

Four-channel transmitter CADET 4 V3 2.4GHZ FHSS

  • two cross drivers with mechanical trims in mode 1 (throttle right))
  • Switch sense deflections for all channels
  • switchable mix flying wing or V-tail
  • the charging connector for transmitter battery (4.8 V)
  • operating status indicator with 2 LED
  • button for pairing and control range
  • audible low voltage signal transmitter batteries

Six-channel receiver RX-600 V3 (single antenna)

Pairing sets RC Cadet 4 Protocol V3

  • 1. For pairing the transmitter and receiver must be located at a mutual distance greater than one meter. Turn on the transmitter.
  • 2. Press and hold the SET button on the receiver and the receiver on. When the red LED on the receiver starts flashing, release the button.
  • 3. Within 10 seconds, then press and hold the BIND button on the transmitter until all LED on the transmitter and the receiver begin to glow continuously lit. Release the button; the transmitter is ready for operation.
Transmitter CADET 4 V3
Number of channels 4
System 2.4GHz FHSS Protocol V3
power 4.8 V (4 x AA alkaline batteries or NiMH battery)
Receiver RX-600 V3
Number of channels 6
System 2.4 GHz FHSS Protocol V3
Fail-safe Yes
power 4.8 to 6.0 V
Dimensions 35x25,3x13 mm
Weight 8 g

Doporučené příslušenství