FLYFUN - 100A - HV regulator - Sale!

Programmable microprocessor controller for brushless motors without sensors ( "brushless, sensorless") designed by taking advantage of the most advanced semiconductor technology with excellent usability characteristics while maintaining a simple and user-friendly service. Serves to control the speed of AC motors in model aircraft or helicopters power NiCd / NiMH and Li-poly / Li-ion / Li-Fe. The power part of the regulator is electrically isolated from the control electronics to ensure high noise immunity at high operating current and high supply voltage. The controller is equipped with stabilizer supply for receiver and servos. For easy adjustment controller is a special LED programming card Hobbywing, which is available separately.

DESCRIPTION AND FUNCTION CONTROLLER

• Extremely low internal resistance and high current carrying capacity thanks to a new generation of power MOSFET transistors.
• Suitable for the vast majority of aircraft brushless motors with power from the battery 5-12S LiPo / Li-ion or Article 15-36. NiCd / NiMH.
• For the supply of NiCd, NiMH, Li-poly, Li-ion, Li-Fe
• Galvanically separate between the power section using optoelectronic element.
• Filtering capacitors with extremely low internal resistance ( "low ESR") increase resistance to unwanted interference.
• The protective circuit eliminates sparks when connecting the drive battery to the controller.
• Adjustable timing for optimum adaptation to a given engine.
• Adjustable PCO circuit - disconnect the motor at a supply voltage drop.
• Safe switching (prevents the motor starts at power).
• Overload protection (when the temperature reaches 110 ° C controller performance is reduced).
• Automatic throttle control signal loss.
• Continuous linear control gas.
• Special stabilizer for power microprocessor for high noise immunity. < / Li>
• Possibility tachometer sensor connection (connecting kd VEMA of the three cables between the controller and motor) for cooperation with some control systems for helicopters (e.g. V-bar system Mikado).
• Maximum speed is 210 000 rpm (2-pole motors), 70,000 rpm (6-pole motors), 35 000 rpm (12-pole motors).
• Two servo cable - long connection to throttle channel receiver and short for programming with programming card.
• Simple programming and adjustment using LED transmitter or programming card Hobbywing ..
• Span gas for the perfect adaptation of the web control signal RC set.

PROGRAMMABLE FUNCTIONS

• Programmable brake (off - on).
• Optional battery (Li-Po or NC / NiMH).
• Adjustable way off the motor when voltage drop (derating or immediate disconnection).
• Adjustable threshold voltage for disconnecting the motor PCO - protection against excessive battery discharge. (Lithium battery: 2.85 V / cell. 3.15 V /., 3.3 V / cell. NiXX battery: 0% / 50% / 65% of the initial voltage value).
• Resetting the controller settings to factory default settings.
• Adjustable timing (advance) - to increase efficiency and optimal adjustment of the engine - Low (3.75 °), Medium (15 °), High (26.25 °)
• Adjustable soft start for motors with gear and helicopters in three stages: Normal (300 ms) / soft (1.5 s) / Super Soft (3).
• Adjustable number LiPo reliable operation for protection against excessive battery discharge.

PROTECTION FUNCTIONS REGULATOR

• Protection at start: If the engine will not start within 2 seconds after the throttle, the controller disconnects the engine.
• Heat protection: If the controller temperature exceeds 110 ° C, the controller will reduce the output power.
• Signal loss of gas regulator performance is reduced when the signal is missing for 1 s; signal is missing for more than 2 seconds causes full disconnection of the motor. < / Li>
• Spark protection: In the positive (+) power cable controller (thick red wire) is involved in gold-plated connector bridged thin cable. This is a special protective circuit used to eliminate sparking when connecting the drive battery to the controller.

Tip: When ever you first turn on the regulator first calibrate the extent of gas according to the instructions. Only then you can use the controller and other settings using the LED transmitter or programming card.