ARA4302V3BT2
New product
This product is no longer in stock
Availability date:
The package contains an RC model car Arrma Granite 4x4 1:10 BLX RTR, which has installed components: AC motor Company 3200Kv 4-P BL3660Kv, regulator Arrma BLX100, Spectrum servo S651 7kg MG. Transmitter Spektrum SLT3 2.4GHz, multilingual manual in English, German, French and Czech manual.
RC car model Arrma Granite 4x4 1:10 BLX RTR Monster Truck with powerful AC motor Spektrum ™ Company ™ 3660 3200Kv, waterproof regulator Arrma BLX100 for 3S LiPol batteries, more powerful servo control Spektrum S651WP MG. RC set Spektrum ™ The remote-controlled car model with a center engine and 4x4 drive will provide maximum traction and performance on any surface. Model speed up to 80 km / h.
The RC model of the Granite 4x4 will surprise you with its toughness and durability. It has a stronger chassis, more powerful fatigue-free servo drives and has a steering wheel with foam rims for precise control. New drivers can set the throttle limit to 50% or 75% until they are ready to use the full speed potential. The SLT3 ™ transmitter is compatible with Tactic® SLT ™ receivers for the operation of older Arrma RTR cars and has a third channel to control optional functions such as lights and winches. The monster truck with all-wheel drive is equipped with a powerful AC motor BLX 3200KV, which gives the model an endless stream of power. The RC model is equipped with rear wheelies to prevent the RC model from tipping over when adding throttle. The controller, with support for 3S LiPo batteries, provides a choice between three driving modes, just choose and start racing.
Several changes in reinforcement were made on the chassis, for greater rigidity. At the same time, aluminum was used on the axle pin retaining plates. The chassis design is arranged in a proven component layout to achieve perfect balance. Drive shaft in the middle, battery on one side and electronics on the other. In addition, the entire chassis is equipped with side covers that limit the ingress of dirt into the chassis. The battery is firmly seated in place using straps.
The "Pull" board area has been increased for better mounting and handling of the drive module.
The motor can be adjusted and the inter-tooth clearance precisely adjusted when replacing the pinion or gear thanks to the aluminum plate with grooves for mounting the motor.
All rotating parts are mounted in ball bearings. Exposed bearings are protected against dust and dirt by rubber caps.
The model received a new more powerful servo and a new more efficient servo saver was used for its maximum protection. This ensures a higher level of impact protection and safer driving.
As with the 4S version, grooved shafts are used here, which can easily transfer the high power of the AC motor. / p>
DBoots FORTRESS MT tires are glued to MT 2.8 "(14mm hex) spoked wheels. Wheels with a strong pattern will give you maximum grip on all surfaces.
Patented oil dampers absorb every impact of the model. The shock absorbers are equipped with impact protection covers on the front. Stiffness and ground clearance can be changed with oil viscosity or spacers. silicone O-rings are used to safely retain the oil.
For even more endless fun, the model has been fitted with adjustable rear wheels that prevent the model from tipping over when full throttle is added.
The drive unit consists of a BLX 3660 AC motor and a BLX100 AC controller. Each of these units forms a separate modular system.
The engine module is removed from the chassis as a complete unit, removing one bolt. Includes engine, engine plate, clutch assembly and transmission cover.
The electronics module consists of a waterproof receiver box, servo board and controller holder. The unit is dismantled and is available for maintenance and service needs.
The model is equipped with front and rear differentials, which ensure maximum traction. The differentials are equipped with high-quality metal gears for trouble-free operation. The wheel drive is transmitted by means of telescopic half-axles.
The pins at the ends of the shock absorbers are fastened in the shock absorber towers on both sides, therefore they do not twist and a stronger fastening of the shock absorbers is guaranteed.
The new Spectrum S651 7kg MG MG servo has 15% more torque than the previous ADS-7M servo. It is waterproof, has metal gears and a torque of 7.27 kg.cm at 6V.
The model is powered by a powerful 4-pole AC motor BLX 3660 3200 rpm // V. The four-pole design gives the motor a linear curve from low speeds. The metal black anodized case not only looks great, but allows better heat dissipation to the passive cooler. 4 mm pin connectors allow easy disconnection for easy engine maintenance.
The BLX100 AC regulator with a current load of up to 100A, in combination with 3S LiPo batteries will provide incredible power. The built-in fan ensures sufficient cooling even at full load. The controller has driving modes, battery underload protection and overvoltage protection. Voltage BEC 6V. Waterproof * switch on the controller. IC5 battery connector.
Adjustable parameters:
The basic 3-channel Spectrum SLT3 transmitter operating at 2.4 GHz is compatible with the SLT protocol. The light weight of the Spectrum SLT3 transmitter allows you to hold without fatigue. The steering wheel is covered with a foam rim for a firm grip. The layout of the controls is practical and intuitive - all controls are positioned so that they are quickly accessible when needed. A secure loop is available for fastening to the strap.
The SLR300 3-channel car receiver is equipped with 2.4GHz, interference-resistant SLT FHSS technology. It is compatible with Spektrum SLT transmitters and is backward compatible with Tactic steering wheel transmitters.
The new IC5 connectors have a modern design with an emphasis on safety and simplicity. The contacts are made of gold-plated pins and sockets with a diameter of 5 mm.
As already mentioned, the connectors have been designed with an emphasis on safe and easy use. The connectors cannot be reversed, the contacts and soldered connections are covered with a plastic cover. The IC5 connector is backward compatible with EC5.
* For information on water resistance specifications, refer to the operating instructions. Tips and tricks for operating in a wet environment can be found in the blog.
To put the model into operation, 4x AA batteries for the transmitter, a drive battery and an adequate charger for the drive battery are required.
The model can be operated on a 2 to 3 cell LiPo battery or a 7 cell NiMH battery. The battery should be equipped with an EC5 or IC5 connector. We recommend a 2-cell LiPo battery (7.4 V) for normal riding.
Spektrum batteries with Smart technology are currently the most modern and safest way to maintain and charge batteries. You can find the advantages of Spektrum Smart technology here.
NiMH batteries are not difficult to handle and are therefore suitable if the RC model car is operated by children (NiMH batteries will not be destroyed by complete discharge). However, NiMH batteries have a lower capacity, so driving time will be slightly shorter.
If you decide to use modern Smart LiPo batteries in the RC model of the Arrma car, then we recommend this charger:
To connect the battery to these chargers, you need an IC5 / IC3 charging adapter.
For normal RC car operation, you need tire glue, bolt glue, a tool kit and silicone shock absorber oil. From our range we recommend an affordable set of tools for RC cars.
The tire glue adheres the tires to the rim of the disc. It is always necessary that the tire is firmly glued to the wheel rim around the entire circumference! If the tire is not stuck around the entire circumference, it may rupture. The tire adhesive has a special composition that is able to bond materials such as rubber or nylon, and at the same time the adhesive is flexible after hardening. We recommend Robitronic Tire Glue from our offer - see recommended accessories / p>
Sometimes it is necessary to add silicone oil to the model's shock absorbers and change the oil in the differentials. During normal operation, there is only a slight leakage of silicone oil along the shock absorber piston rods. If the damper piston rod surface or seal condition is in poor condition, the oil leak may be large. Repair kits or individual parts are supplied for these cases. From our range of silicone oils, we recommend TLR (Team Losi Racing) silicone oils, see recommended accessories.
Screw glue is required for routine maintenance. Screws screwed into the metal material (eg screws in the motor, set screw in the pinion) must be secured against loosening with this adhesive.
Protective covers are designed to reduce the risk associated with transporting and charging batteries. LiPo batteries can, while maintaining small dimensions and low weight, provide high discharge currents and have a large capacity for long travel times. On the contrary, the LiPo battery is particularly susceptible to mechanical damage.