FOXY R35B CAR AC adapter 35A + prog.card (sensorless)"

Programmable AC controller for car models. Permanent current 35A (peak 190A), power 5-10NC / 2-3 LiPO cells, weight 70g, BEC 6V / 2A. Supplied with an LED programming card."


New product


Prodej skončil

More info

Doporučené příslušenství

More info

Programmable electronic controller for brushless motors for model cars respectively. and ships. It is designed for speed control of AC motors without sensors ( "sensorless") RC cars in the scales 1:16 to 1:10. Using advanced MOSFET power transistors and aluminum heat sink with active cooling fan ensures high current-carrying capacity with small dimensions and low weight. Powerful switching power stabilizer SBEC built-in regulator ensures top performance servo control - no matter how fast and strong, always for them, you have enough power! The controller can be quickly and easily programmed using cards FOXY CAR 1:10 Card supplied in the base set.


  • Programmable using the enclosed card FOXY Card CAR 1:10
  • Switching SBEC 6.0 V / 2 A
  • Power: 2-3S LiPo or Li-Fe / 5-10 NiXX
  • Active cooling fan
  • Protection: PCO, congestion, loss of control signal, motor stall
  • Driving modes: Forward / Brake, Forward / Brake / Reverse
  • Span gas control


  • PCO voltage protection against excessive discharging of the drive battery (with automatic detection of the number of articles voltage for engine shutdown 2.6 V / C., 2,8V / Art., 3.0 V / C., 3.0V / Art. 3 2 V / C).
  • Driving modes to select bidirectional or unidirectional mode (Forward / Pause / Reverse, Forward / Brake (no return), Forward / Reverse)
  • Adjustable timing (advance) - to increase the efficiency and optimization of the engine (5 values; low ... very high)
  • Initial acceleration - reduces engine power during acceleration from a standstill (4 values; low ... very high - for a smooth start slow or rapid "tapping" with turning the wheel)
  • Performance for Reverse - sets the power that is available for the reverse (20%, 30%, 40%, 50%, 60%, 70%, 80%, 90%, 100%)
  • Limit gas - allows to limit the power which is available for forward (0%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 90%) and for a beginner, who still can not cope with sensitive working gas enjoyable driving. < / Li>
  • Intensity braking - in "unicast" driving mode set možňuje effect braking at full throttle pushing away (10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 100%).
  • The intensity of the brake in the neutral position - in a "bidirectional" driving mode with a pause in neutral to set the effect of the brake (0%, 4%, 8%, 12%, 15%, 20%, 25%, 30%) when the throttle in the neutral. It mimics the behavior of a model with DC motor.
  • Direction of rotation - allows you to select motor rotation clockwise or counterclockwise.
  • Neutral range - sets the width of the "deadband" around the driver neutral gas (2%, 3%, 4%, 5%, 6%, 10%). The lower the value, the narrower the deadband, and the smaller displacement from neutral control is necessary to make the car started to accelerate. A higher value gives a wider deadband.
  • Resetting the controller to factory default settings


  • Thermal Protection: The controller has built-in protection, which cuts the engine when the controller temperature exceeds 95 ° C. Launch of protection is indicated by LEDs on the controller.
  • Fan: Power supply cooling fan is provided from the controller. The power cable is however possible to disconnect a fan powered from an external source (max. 14 V, for example. 2-3s Li-poly battery or šestičlánek NiCd / NiMH) to ensure cooling of the controller in the pits even when not connected drive battery

Card Programming card FOXY CAR 1:10

Programming card for controllers FOXY CAR with four-digit LED display. Serve for easy and fast programming controllers - alone at home "on the table" or involved in the model home and on the racetrack.

The controller is connected via servocable socket is located at the top of the card. The card's power is supplied from the regulator (BEC stabilizer using a connected traction battery) or from normal 4-5čl. NiCd or NiMH receiver battery pack attached to the card (while programming the controller itself). FOXY controllers can be programmed in the model and the connected motor - for safety reasons, but we recommend that when programming model placed on a stand with wheels in the air - to avoid any possible accident at any omissions or operator error.

For programming, the foursome buttons:

tl. MENU to scroll between functions tl. VALUE (value) sets the value of the function, Tl. OK to confirm the value set and stored in the memory controller (stored in the memory is indicated by red LED flashes on the card and at the same time on the controller) tl. RESET is used to return the set values \u200b\u200bto the factory default settings.

Functions and their values \u200b\u200bare displayed on the four digit LED display - left two digits indicate the serial number of program functions; two digits to the right of the set value.

List of features and possible values \u200b\u200bcan be found on a label on the card.

Note .: The card can not be used to program the controllers FOXY CAR 1: 8 or air controllers FOXY.

Use Auto, Boat
Type alternate
Sustained current [A] 35
Max. peak current [A] 190
NiXX 5-10
LiXX Articles 2-3
BEC voltage [V] 6
BEC current [A] 2
Length [mm] 40
Width [mm] 28
Height [mm] 31
Weight [g] 70
Regulation bidirectional
Brake Yes
Input for sensors No
programmable Yes
On-road car Off-road car
Limit engine (2S LiPo 6čl. NiMH) > 9 Thread > 12 thread
Limit engine (3S LiPo 8-9čl. NiMH) > 12 thread > 18 thread

Doporučené příslušenství