LYNX 4S 2,4GHz + RX Proton 4

LYNX 4S is a new steering computer RC Hitec for racing and recreational riding modelers. During its construction, the main consideration was put on the practical implementation of the cabinet, ergonomics layout controls, adjustable steering wheel position in a wide range ambidextrous, ease of programming with an intuitive menu and the ability to "serve" the most competitive and recreational model cars and speed boats.

Cabinet: LYNX 4S has at first glance simple, soberly elegant box with a handle with a soft non-slip handle which fits nicely in your hand.

Controls: To control the main functions (steering and throttle) used the exact driver with adjustable force neutralizing force. The steering wheel can be positioned on either side of the transmitter to control the right and left hand; using extension adapter can be placed eccentrically plus navigate virtually any angle. The throttle has an adjustable mechanical stop brake software can switch the ratio of gas / brake (return) 50:50 or 70:30. Digital trims have a sound signal jog, mid and end positions, and graphical display positions on the display. They are positioned around the steering wheel and are programmatically assignable. Two additional proportional channels, switching on and off program functions and mixes or adjusting their values \u200b\u200bcan be in charge next programmatically assignable controls:

• three-position slide switch on the steering wheel
• knob / button on the top panel
• latched pushbutton switch on the top panel
• 2 knobs in the handle (accessible from both sides)
• button on the handle (on both sides)
• 3 digital trim around the wheel

All controls are freely assignable.

Power transmitter: LYNX 4S allows you to use a wide variety of power sources: NiMH battery pack with 4-cell or two-car sets LiPo, LiFe, Li-ion. The battery voltage is displayed on the screen in numerical and graphical form. NiMH batteries can be charged without removing it from the transmitter via built-in charging connector.

Transmission system: Transmitter LYNX 4S is a four channel transmitter operating in the 2.4 GHz band; control models, you can use one of two transport protocols:

• super fast unidirectional AFHSS protocol HHR (Hitec High Response) with two-channel receiver AXION 2 allows you to achieve ultra-short response system ( "latency"), which together with the control signal with a higher repetition rate ( "frame rate") of 4 ms guarantees a truly lightning fast response management for top racing riding. This of course requires the use of digital servos with corresponding characteristics (receiver AXION 2 only works with digital servos, analog are not able to signal with a repetition rate of 4 ms work).
• bi-directional telemetry AFHSS protocol is working with miniature receivers AXION 4 and telemetry receiver PROTON fourth Allows use is still very high repetition rate of 7 ms (only digital servos); For less demanding applications in models with analog servos you can select the transmission speed NORMAL (14 ms). When using telemetry receiver transmitter PROTON 4 course offers displaying telemetry data display (speed, speed, temperature, supply voltage receiver) with voice output to the built-in speaker or headphones connected.

Memory: Transmitter LYNX 4S has a memory for 30 models, which can extend through the slot for a micro SD card for additional 30 models on the card. The card is additionally played messages voice output or telemetry, and music (.wav) - The report file can be easily edited.

User interface: To program the transmitter programming, the rotary roller / button and double click (for convenient access to the steering wheel left and right), along with a backlit graphic LCD display. Programming roller used to move within the program menu and setting values; his grip opens the field for the selected parameter setting or confirms the setting. Additional key "ESC" button to return to the previous menu level or parameter. Alarms can take place via audio or voice signals from the internal speaker (or. Of headphones if you connect it) or by vibration.

Software: The software is divided into menu Operating Instructions transmitters for traffic monitoring and telemetry display and programming menus for setting transmitter systems and programming model. The program menu is lucidity still divided into two sections with the program functions and mixes, system settings section, a section for memory models and a section for working with data on the SD card.

Operating menu is used for operating the transmitter in normal operation - displays the type and name of the chosen model, used receiver type, position digital trims, voltage transmitter, total operating time, detail timekeeping, setting double deflection control and setting deflections brakes. Turn the roller programming can go to the menu display telemetry (if telemetry receiver in the model PROTON 4)

System setup is used for setting basic functions such as choosing the type of receiver and the used transmission protocol pairing (pairing is specific to each individual model memory) calibration Steering and gas servo monitor with a graphical representation of the signal in each channel, setting the parameters for telemetry , adjustment of transmitter (type battery pack, alarm, contrast and backlight etc.).

Menu for memory model enables the creation of a new model, copying and deleting the contents of memory, setting the model name (up to 12 characters), etc. < / P>

Menu for working with data on the SD card allows copying models from memory cards transmitter and vice versa, copying and deleting models on the card, setting the parameters for telemetry voice output and music playback.

Two menus with program functions include everything you need to control your model:

• Perfecting sense deflections
• Resize (end points) travels (EPA)
• The intensity of braking (ATL)
• Anti-lock braking system (ABS) - Set intermittent automatic braking with adjustable intensity and repetition rate triggered by adjustable brake actuator position. ABS activity may also influence the deflection of the steering wheel for optimum setting for driving on a plane / in mild or sharp turns
• Exponential control - allows you to set exponential control response to reduce steering sensitivity around neutral
• Exponential brakes - allows you to adjust the brake exponential response to softer or vice versa sharper response near neutral Drivers brake / gas
• Exponential gas - feature allows not only to set the throttle response as a smooth exponential curve, but also as curve 3, 5 or 7 points.
• Dual control displacements (deflections for quick setup procedure for the drive knob on the handle or switch)
• Servo trim for fine adjustment of the neutral position in all four channels
• Fail-safe - Emergency deflection fail-safe set independently for each channel in HOLD mode (hold last correct deflection) or SET (servo moves to pre-programmed emergency position).
• Boost - automatic acceleration when starting (for fast acceleration on the track slippery and inconsistent surfaces - enables smooth start without wheel spin, when the skew control gas exceeds a preset limit, can automatically throttle)
• Speed \u200b\u200bservo control - allows you to set different speed servo control to move from the center to the sides and to return back
• The speed of the throttle servo - allows you to adjust the speed of movement of the throttle servo or speed controller response to move from neutral to full gas other than to return to neutral. Speed \u200b\u200bservo acceleration may have a single value for the entire range, or two or three different sections for adjustable deflection of the driver gas.
• Gas mode - allows you to adjust the ratio of forward / backward (brake) at 50:50 or 70:30
• Safe idle (Idle Up) - allows you to change the servo throw gas on a pre-programmed step assigned switch. This function is useful eg. When the service pit stop when you leave the throttle at idle, but idling changeover switch secure him a little raise, so the engine certainly does not disappear, but the clutch still does not work.
• The timer - allows measurement of time up (stopwatch) or down (timer) with adjustable time to start beeper (1-60 minutes) and additionally pre-signaling (60 seconds) before this time. Timekeeping is possible to execute the assigned switch or throttle control. The timer can also be operated in measurement of individual wheels - in this case, measures the total time and press the assigned switch records the time passes each wheel
• List of lap times - times tables allows viewing of individual wheels, moreover, indicates the total time and average lap time
• Assigning switches - allows virtually unlimited assignment switches and trim digital control channels, mixers and switching parameters of program functions
• Assign buttons - allows you to assign knobs for channel control and parameter setting program functions while driving
• Channel mixing - mixing channel transmitter provides for 11 types of models:
• a simple model without mixers,
• Several versions of mixing for cars 1: 1.8: 5 with separate channels for gas and brake, the two brake control split into two channels for the left and right wheel,
• Mix for trial / crawlers with independently controlled front and rear (4WS) for models with two engines and a combination of the two motors / control front and rear wheels,
• Mix for a boat with two rudders. < / Li>

Data socket: Software transmitters can be updated via USB interface HPP-22, just as is the case with other Hitec transmitters.

Telemetry: With telemetry receiver PROTON 4 may LYNX 4S on the display for information on supply voltage receiver and speed measurement model and the GPS sensor built-in receiver. If you connect a temperature sensor and a magnetic sensor speed, you will see the figure of temperature and speed. The speed can then be based on data from a GPS or a tachometer. For each measured variable, you can set the threshold at which an alarm (display, audible beeps or voice, vibration).

SD card: Slot for micro SD card memory expansion allows the transmitter by a further 30 models, backing up the contents of the memory of the transmitter. On the SD card stores files in ".wav" with messages for telemetry, voice output (default set of "messages in English can be found in the" Downloads "), respectively. music files (the format ".wav"). In the "Downloads" you will find a simple PC program for creating your own "playlists" conversion from MP3 files.

Headphone jack: Lets you connect headphones for voice output or telemetry audible alarm.

LYNX 4S can be mounted after the curtain comes with the transmitter around the neck with straps Hitec standard.

RC kit includes:

• Transmitter LYNX 4S
• The transmitter battery 4.8 V NiMH
• Receiver PROTON 4
• Operating Instructions