D485HW standard digi servo (7.5kg)

Standard servo with new generation plastic gears with electronics with lightning fast response for general use. Programmable, 4.8-7.4V power supply. Thrust 5.2kg.cm, speed 0.20s / 60 ° at 4.8V, thrust 7.5kg.cm, speed 0.15s / 60 ° at 7.4V. Replacement of HS-548

1HI38795

New product

Hitec

In stock: > 10 pcs
Stores and delivery dates
Price with VAT:
(DPH CZ 21%)
28,73 € 27,31 €
Price without VAT
22,57 €

-1,42 €

B B

More info

Spare parts

Recommended accessories

More info

Servo Hitec D Series

The new Hitec D series digital servos combine the ultra-fast response, accuracy and high resolution of 4096 steps of the HS-8xxx servo series with HS-7xxx servo programming options. In fact, existing servos far outweigh the 32-bit processor and the 12-bit ADC converter. In addition, they offer the "Wide Voltage" function, allowing the use of battery power in a wide range of rated voltages of 4.8 to 7.4 V.

32bit MCU / 12bit ADC

The new 32-bit Hitec processor coupled with a 12-bit analogue-to-digital converter that converts the signal from the feedback potentiometer offers the best response between servos for RC models so far. You can also use the universal PC interface DPC-11 (applicable to all Hitec programmable servos) to fine-tune your D-Series servo drives to maximum performance (scaling, resolution, fail-safe, soft start, etc.) in a wide range of applications.

Wide Voltage

The Hitec "Wide Voltage" technology supports all types of receiver batteries with a nominal voltage of 4.8-7.4 volts. This means that the servo can be powered directly, for example, by NiMH or NiCd batteries, two LiFe, LiPo or Li-ion batteries - Of course, it must be remembered that the thrust and speed of the servo depend on the size of the supply voltage.

Output shaft with a tiny 25-teeth

The D-servo output shaft is standard with a 25-tee (including a more precise lever adjustment perpendicular to the longitudinal axis of the servos) and new levers with a corresponding thrust are used (not compatible with older Hitec servos).

Soft start

The soft start protects the servo and the rudder control mechanism when the onboard electronics is switched on - the servo slowly moves to the neutral position after switching on - no sudden twisting

Smart

New control algorithm to prevent spontaneous servicing of the servos in the "sharp" setting of the servo's deadband, saving gears and reducing current consumption."

Programmable features

With the new DPC-11 Programmer / USB Interface, you can set a number of D servo parameters for the perfect servo adaptation of your application. Series D servos have a consistently high resolution; with the "EPA" function, you can set the servo deflection range up to 180 ° (with the control signal with 0.9-2.1 ms pulses). Programmable values \u200b\u200bare:

  • reset to factory defaults
  • deadband bandwidth (adjustable in 10 steps)
  • sense of rotation
  • speed of rotation
  • neutral
  • soft start
  • Depth (up to 180 °)
  • enable or disable fail-safe
  • the fail-safe emergency setting
  • overload protection (0-50% overload limitation)

D485MW

Standard servo with carbon drive gears with output shaft mounted on two ball bearings for use in RC models of all types. Thanks to its low price, it is an excellent replacement for analogue standard servos with higher pull, higher hold and programming capabilities - even in regular holiday models.

It will replace HS-5485HB and HS-5495BH in the future.

Servos size Standard
Servo type digital
Stroke at 4.8V [kg / cm] 5.2
Stroke at 6.0V [kg / cm] 6.4
Tension at 7.4V [kg / cm] 7.5
Speed \u200b\u200bat 4.8V [s / 60h.] 0.2
Speed \u200b\u200bat 6.0V [s / 60h.] 0.17
Speed \u200b\u200bat 7.4V [s / 60h.] 0.15
Servo gears carbonitates
Ball bearings 1xBB
Highvoltage Yes
Power [V] 4.8 - 7.4
Length [mm] 39.8
Width [mm] 19.8"
Height [mm] 38
Weight [g] 45
Intended for airplanes, sailing boats, boats
Number of teeth of the spindle 25
Resistance to water No
"

Spare parts

Recommended accessories