> 10 pcs
|Place to pick up||Delivery|
|Store Českobrodska 566, Praha 9, 19800||Immediately|
|Store OC Lužiny Archeologická 2256/1, Praha 5, 15500||Tomorrow from 16:00|
|Mode of transport||Delivery|
|Gibon delivery - Express delivery Prague||Mon 18.02.17-22h|
|DPD Private- Delivery to the Czech Republic||Mon 18.02.|
|Czech Post||Mon 18.02.|
|PPL - Delivery to the Czech Republic||Mon 18.02.|
|Mode of transport||Delivery|
|DPD - Delivery to the Slovakia||Tomorrow|
|GLS - Delivery to the Slovakia||Mon 18.02.|
|PPL - Delivery to the Slovakia||Tomorrow|
|DPD - Delivery to Germany||Tue 19.02.|
|DPD - Delivery to Poland||Tue 19.02.|
|DPD - Delivery across Europe||2 - 4 days|
|GLS - Delivery across Europe||3 - 4 days|
|PPL - Delivery across Europe||3 - 4 days|
Warning: Last items in stock!
Servo Hitec D Series
The new Hitec D series digital servos combine the ultra-fast response, accuracy and high resolution of 4096 steps of HS-8xxx Servers with HS-7xxx Servers. In fact, existing servos far outweigh the 32-bit processor and the 12-bit ADC converter. In addition, they offer the "Wide Voltage" function, allowing the use of battery power in a wide range of rated voltages of 4.8 to 7.4 V.
32bit MCU / 12bit ADC
The new 32-bit Hitec processor coupled with a 12-bit analogue-to-digital converter that converts the signal from the feedback potentiometer offers the best response between servos for RC models so far. You can also use the universal PC interface DPC-11 (applicable to all Hitec programmable servos) to fine tune your D-Series servo drives to maximum performance (scaling, resolution, fail-safe, soft start, etc.) in a wide range of applications.
The Hitec "Wide Voltage" technology supports all types of receiver batteries with a nominal voltage of 4.8-7.4 volts. This means that the servo can be powered directly, for example, by NiMH or NiCd batteries, two LiFe, LiPo or Li-ion batteries - Of course, it should be remembered that the thrust and speed of the servo depend on the size of the supply voltage.
The soft start protects the servo and the rudder control mechanism when the onboard electronics is switched on - the servo slowly moves to the neutral position - no sudden jerking occurs.
New control algorithm to prevent spontaneous servicing of the servos in "sharp" setting of the servo insensitive band, saving gears and reducing current consumption.
With the new DPC-11 programmer / USB interface, you can set a number of D servo parameters for the perfect servicing of your application's servos." Series D servos have a consistently high resolution; You can set the servo deflection range up to 180 ° with the "EPA" function (with the control signal with 0.9-2.1 ms pulses). Programmable values \u200b\u200bare:
A monster-strong Jumbo-sized servo with steel gears with output shaft mounted on two ball bearings. Thanks to the dustproof and waterproof housing (International Protection Code IP-67, it completely prevents contact with dust, with immersion in water to a depth of 1 m for 30 minutes of test run) is particularly suitable for large seaplanes, off-road models, And submarines - just to places exposed to dust and moisture, high demands on pulling power and overall mechanical resistance of the servos.
|Stroke at 4.8V [kg / cm]||32.5|
|Stroke at 6.0V [kg / cm]||40.5|
|Stroke at 7.4V [kg / cm]||50|
|Speed \u200b\u200bat 4.8V [s / 60h.]||0.26|
|Speed \u200b\u200bat 6.0V [s / 60h.]||0.21|
|Velocity at 7.4V [s / 60st.]||0.17|
|Power [V]||4.8 - 7.4|
|Height [" Mm]||62|
|Intended for||Airplanes, road cars, car parks, sailboats, boats|
|Resistance to water||Waterproof|