D945TW very strong digi servo (23kg)"

Powerful and fast digi servo with new-generation titanium gears with lightning-fast electronics for demanding use. Programmable, power supply 4.8-7.4V. Stroke 14kg.cm, speed 0.16s / 60 ° at 4.8V, ta"

1HI38804

New product

Hitec

In stock: > 10 pcs
Stores and delivery dates
Price with VAT::
138,60 € 131,69 €
Price without VAT:
108,84 €

-6,91 €

B B

More info

Náhradní díly

Doporučené příslušenství

More info

Servo Hitec D Series

The new Hitec D series digital servos combine the ultra-fast response, accuracy and high resolution of 4096 steps of HS-8xxx Servers with HS-7xxx Servers. In fact, existing servos far outweigh the 32-bit processor and the 12-bit ADC converter. In addition, they offer the "Wide Voltage" function, which allows the use of battery power in a wide range of rated voltages of 4.8 to 7.4 V.

32bit MCU / 12bit ADC

The new 32-bit Hitec processor coupled with a 12-bit analogue-to-digital converter that converts the signal from the feedback potentiometer offers the best response between servos for RC models so far. You can also use the universal PC interface DPC-11 (applicable to all Hitec programmable servos) to fine tune your D-Series servo drives to maximum performance (scaling, resolution, fail-safe, soft start, etc.) in a wide range of applications.

Wide Voltage

The Hitec "Wide Voltage" technology supports all types of receiver batteries with a nominal voltage of 4.8-7.4 volts. This means that the servo can be powered directly, for example, by a NiMH or NiCd battery of four to six cells, two LiFe, LiPo or Li-ion batteries - Of course, it should be remembered that the thrust and speed of the servo depend on the size of the supply voltage.

Output shaft with a 25-teeth long-lever

The D-servo output shaft is standard with a 25-tee (including a more precise lever adjustment perpendicular to the longitudinal axis of the servos) and new levers with a corresponding thrust are used (not compatible with older Hitec servos).

Soft start

The soft start protects the servo and the rudder control mechanism when the onboard electronics is switched on - the servo slowly moves to the neutral position after switching on - no sudden twisting

Smart

New control algorithm to prevent spontaneous servicing of the servos in "sharp" setting of the servo insensitive band, saving gears and reducing current consumption."

Programmable features

With the new DPC-11 programmer / USB interface, you can set a number of D servo parameters for the perfect servicing of your application's servos. Series D servos have a consistently high resolution; You can set the servo deflection range up to 180 ° with the "EPA" function (with the control signal with 0.9-2.1 ms pulses). Programmable values \u200b\u200bare:

  • Reset to factory defaults
  • Deadband bandwidth (adjustable in 10 steps)
  • Sense of rotation
  • Speed \u200b\u200bof rotation
  • neutral
  • Soft start
  • Displacement size (up to 180 °)
  • Enable or disable fail-safe
  • Setting the fail-safe emergency shift
  • Overload protection (0-50% overload limitation)

Splash Proof

The servos are resistant to splashing water and moisture (they are not intended for permanent immersion under water). Thanks to this, they are also suitable for use in harsher conditions in RC cars, boats and other models where the servos are exposed to weathering.

D945TW

Strong and fast servo with titanium gears with output shaft mounted on two ball bearings for use in RC models of all types. Especially suitable for RC helicopters, aerobatic and 3D models of 3-6 kg aircraft, racing RC cars 1: 10/1: 8 and similar applications with high demands on speed and pulling power.

It will replace HS-7945TH and HS-8370TH in the future.

Servos size Standard
Servo type digital
Stroke at 4.8V [kg / cm] 14
Stroke at 6.0V [kg / cm] 18
Stroke at 7.4V [kg / cm] 23
Speed \u200b\u200bat 4.8V [s / 60h.] 0.16
Speed \u200b\u200bat 6.0V [s / 60h.] 0.12
Speed \u200b\u200bat 7.4" V [s / 60st.] 0.1
Servo gears Titanium
Ball bearings 2xBB
Highvoltage Yes
Power [V] 4.8 - 7.4
Length [mm] 40
Width [mm] 20
Height [mm] 38
Weight [g] 68
Intended for Airplanes, helicopters, road cars, terrain cars, sailboats, boats
Number of teeth of the shaft 25
Resistance to water Splashproof (p
"

Náhradní díly

Doporučené příslušenství