|Place to pick up||Delivery|
|Store Českobrodska 566, Praha 9, 19800||Today from 14:30|
|Store OC Lužiny Archeologická 2256/1, Praha 5, 15500||Today from 16:30|
|Mode of transport||Delivery|
|Gibon delivery - Express delivery Prague||Today 17-22h|
|DPD Private- Delivery to the Czech Republic||Tomorrow|
|PPL - Delivery to the Czech Republic||Tomorrow|
|Mode of transport||Delivery|
|DPD - Delivery to the Slovakia||Fri 16.11.|
|GLS - Delivery to the Slovakia||Mon 19.11.|
|PPL - Delivery to the Slovakia||Fri 16.11.|
|DPD - Delivery to Germany||Mon 19.11.|
|DPD - Delivery to Poland||Mon 19.11.|
|DPD - Delivery across Europe||2 - 4 days|
|GLS - Delivery across Europe||3 - 4 days|
|PPL - Delivery across Europe||3 - 4 days|
Warning: Last items in stock!
Servo Hitec D Series
The new Hitec D series digital servos combine the ultra-fast response, accuracy and high resolution of 4096 steps of HS-8xxx Servers with HS-7xxx Servers. In fact, existing servos far outweigh the 32-bit processor and the 12-bit ADC converter. In addition, they offer the "Wide Voltage" function, which allows the use of battery power in a wide range of rated voltages of 4.8 to 7.4 V.
32bit MCU / 12bit ADC
The new 32-bit Hitec processor coupled with a 12-bit analogue-to-digital converter that converts the signal from the feedback potentiometer offers the best response between servos for RC models so far. You can also use the universal PC interface DPC-11 (applicable to all Hitec programmable servos) to fine tune your D-Series servo drives to maximum performance (scaling, resolution, fail-safe, soft start, etc.) in a wide range of applications.
The Hitec "Wide Voltage" technology supports all types of receiver batteries with a nominal voltage of 4.8-7.4 volts. This means that the servo can be powered directly, for example, by a NiMH or NiCd battery of four to six cells, two LiFe, LiPo or Li-ion batteries - Of course, it should be remembered that the thrust and speed of the servo depend on the size of the supply voltage.
Output shaft with a 25-teeth long-lever
The D-servo output shaft is standard with a 25-tee (including a more precise lever adjustment perpendicular to the longitudinal axis of the servos) and new levers with a corresponding thrust are used (not compatible with older Hitec servos).
The soft start protects the servo and the rudder control mechanism when the onboard electronics is switched on - the servo slowly moves to the neutral position after switching on - no sudden twisting
New control algorithm to prevent spontaneous servicing of the servos in "sharp" setting of the servo insensitive band, saving gears and reducing current consumption."
With the new DPC-11 programmer / USB interface, you can set a number of D servo parameters for the perfect servicing of your application's servos. Series D servos have a consistently high resolution; You can set the servo deflection range up to 180 ° with the "EPA" function (with the control signal with 0.9-2.1 ms pulses). Programmable values \u200b\u200bare:
Strong servo with metal gears with output shaft mounted on two ball bearings for use in RC models of all types. Especially suitable for RC models of 2-5 kg \u200b\u200baircraft, RC cars 1: 10/1: 8 and similar applications.
In the future, it will replace Servos HS-5645MG and HS-5685MH.
|Stroke at 4.8V [kg / cm]||8.3|
|Stroke at 6.0V [kg / cm]||11.3|
|Stroke at 7.4V [kg / cm]||12.9|
|Speed \u200b\u200bat 4.8V [s / 60h.]||0.28|
|Speed \u200b\u200bat 6.0V [s / 60h.]||0.2|
|Velocity at 7.4V [s / 60st.]||0.17|
|Power [V]||4.8 - 7.4|
|Intended for||Aircraft, helicopters, road and" Uta, car terrain, sailing boats, boats|
|Number of teeth of the shaft||25|
|Resistance to water||No|