Warning: Last items in stock!
And here it is! FunCub 300 mm larger, with two such battery and engine power fourfold, large slotted flaps, with hook for aero-tow, bomb bay and ready for attachment of floats - it will be a great deal of fun!
Multiplex again succeeded previously unimaginable - in a single model to combine features and capabilities that are much closer with 3D models, while retaining the option to use as a recreational FunCub XL model for festive pilots. Therefore, in our evaluation of pilot performance will find an unusual figure P2-4 - FunCub when appropriate setting suitable for recreational pilots and seasoned athletes who fully utilize its "Fun XL" potential. Take a closer look, how is this possible ...
FunCub preserves nowadays traditional "multiplexáckou" construction of highly resistant foam ELAPOR which ensures easy and quick construction, light weight, strength and durability in operation and ease of repair if the pilot something goes wrong. Although outwardly similar to its predecessor, proven school, a training and 3D entertainers FunCub, everything is at it more robust, thoroughly reinforced and dimensioned.
The fuselage is made of foam ELAPORu with "multiplexácky" sophisticated internal reinforcement structure made of plywood, laser-carved parts. This forms the "backbone" of the model; supports the motor, controller, drive battery and chassis. Fans of fast buildings will be pleased that construction has strings them in the multiplex. The AC motor is mounted in the nose of the rear mounting. The cowl is removable from ELAPORu with magnetic locks. Removable canopy allows access to bed for the drive battery. Servo rudder and the elevator is in the tail of the fuselage and rudder control short wire rods. In the upper part of the fuselage has a place towhook mechanism with servo control to the bottom of the hull can build a servo-operated cargo compartment door for tuning paratrooper Alfred, candy or other "payload". < / P>
Two-piece wing foamed ELAPORu imitation design slack, and a fabric cover on the upper side and with a carbon tubular main beam is put on the side of the two tubular connectors carbon; halves are secured polyamide screws and a pair of carbon rods wings. Servos and valves are installed into the prepared pits; rudders controlled via a short straight wire rods. Large slotted flaps are suspended on the eccentric plastic hinges allowing deflection of up to 90 ° down. Wing design allows mounting kit LED lights POWER-MULTILIGHT - holders are prepared for LED positioning and landing lights with transparent covers and, of course, grooves and tunnels for laying cables. The roots of the wing halves is stored ingeniously designed mount connectors for cables aileron servos, valves and lights.
The tail surfaces are made of foam ELAPORu indicated with "ribs" and sagging skin; horizontal stabilizer has a carbon rod, the rudder is ready for installation of warning lights.
The main undercarriage has a robust aluminum legs and a giant balloon wheels (with foam-filled tires) for take-off from any field. The spur is duralumin, coupled with springs rudder. Wheeled chassis can easily be mistaken for tuning a set of floats.
FunCub XL is designed to drive the AC motor with an outer diameter of 42 mm, as the original recommended Permax BL-O 4235-0480 or 3530-0570 our FOXY G2 (has the same mounting dimensions) with a 60-85 A speed governor and powered by 6S LiPo battery (3S pair of sets of about 3300 mAh with a load capacity of at least 25C).
To control model you will need at least sedmikanálovou radio system - in this case, but left with channels for auxiliary functions or you have to flap and aileron servos involved Y-cables into one channel. To fully exploit the possibilities of the model with functional towing hook, operated cargo compartment door and lights must be nine, but rather prefer a ten RC rig ..
To control the rudder and auxiliary functions will need 6-8 miniservo - ready to match pits servos Hitec HS-225BB / MG. For float versions with water and rudder for "bush flying" from the taller grass or uneven terrain, it is advisable to fit the rudder servo with metal gears. 6-8 miniservo on board, of course, means that you will need to use a speed controller with a properly sized BEC power stabilizer or external UBEC stabilizer (at least 6A) or receiver battery.
Excess power and highly efficient large flaps and giant wheels are precisely what makes the FunCubu XL "entertainer". It can take off and land on a dime, literally, depends on the propeller taking off and landing as well as from higher grass or uneven ground, where it would have a different model to "operate" could. For summer holidays on the water, you can buy floats - excess engine power and precise control with ailerons and flaps again allow seamless operation and seaplane pilots with no previous experience in naval aviation.
You can also supplement the tow hook (it can be installed at any time, and in addition to finished and létaného model) and XL FunCub turn into a drag that reliably gets to a height of 2-3 m and gliders, as Solius or Heron.
Kit includes: moldings fuselage, wings and tail surfaces of Elaporu, carbon spar, levers, handles and other small accessories including tow-hook and a mechanism for opening the door cargo space, duralumin main chassis and spur lightweight balloon wheels, large sheets of self-adhesive decals and detailed instructions for building and flying. Bag with accessories hover hidden in the packing box (the polystyrene) see. photo.
Tuning: For FunCub XL is a set of floats (Cat. #. # 733098) with which a lot of fun too near the water # 852004 The parachutist Alfred # 73030 Set of lights POWER-MULTILIGHT with remote control (On, Off, position lights + anti-collision beacons, position lights turned on + + landing beacons of light).
Tip To obtain "piperovitějšího" appearance, which is inherently yellow, you can spray the spray model RC Car Colour, color no. 019 Yellow. Make sure you sprinkled a very thin layer 2-3 Cross. If you attempt to spray thick, paint will peel off. Another reason for the investigation of the color is also that a thick layer of paint adds a lot of weight.
|Wing area [dm 2]||51|
|Difficulty piloting||P2, P3, P4|
|controlled functions||S, V, K (2), M, F (2)|
Recommended drive and RC equipment:
|FOXY XL||MPX XL|
|Engine||FOXY G2 C3530-570||Permax BL-O 4235-0480|
|Regulator||FOXY R-85A Combo Set||MultiCONT BL-60 SD|
|power pack||RAY 2x 11.1 V 3250 mAh||2x FOXY 11.1 V 3300 mAh|
|Propeller||APC 14x8 "E||15x8 "*|
|Serva||6-8x HS-225BB or MG|
|RC rig||min. 7 channels, 10 for the full utilization of all functions|