MultiCharger X1 AC Plus Charger"

50W microprocessor fast charger with 1-15 NiCd / NiMH balance, 1-6 Li-poly / Li-ion / Li-Fe, 2-20V Pb current 0.1-6A / 50W. Discharging max. 1A / 5W. Power supply 11-18 V or mains 100-240V / 50-60Hz."

1HI77493

New product

Hitec

Prodej skončil

More info

Doporučené příslušenství

More info

Charger Hitec Multicharger X1 50W AC Plus was designed with the aim to provide everything you need to charge "under one roof", including an AC adapter and a simple operation. Multicharger X1 AC Plus allows you to charge and discharge the normal cell types (NiCd, NiMH, Li-poly, Li-ion, Li-Fe, Pb), the unit has a built-in six-balancer that provides a very safe and comfortable charging lithium batteries. Naturally, there socket for the temperature sensor.

  • The input supply voltage of 11-18 V dc
  • AC 100-240 V / 50-60 Hz
  • For charging and discharging 1-15 NiCd / NiMH cells, 1-6 Li-ion / Li-poly / Li-Fe articles or 2- 20 V lead-acid batteries
  • Adjustable charging current (0.1 A - 6.0 A)
  • Adjustable discharge current (0.1 A - 1.0 A)
  • Max. power to charge 50 W, 5 W for discharging
  • Auto charging and discharging of NiCd, NiMH and lithium batteries with adjustable current limit
  • End charging by regulators delta-peak for NiCd and NiMH batteries
  • # Pb and Lithium batteries are charged using the "constant current / constant voltage"
  • Adjustable sensitivity of delta-peak detection for NiCd and NiMH batteries
  • Repeated cycle operation of charging / discharging or discharging / charging NiCd and NiMH batteries, up to 5 cycles
  • Three charging modes for lithium batteries - fast charging, charging with balancer storage and charge / discharge
  • Termination charge after the set time, supplied charge or limit temperature.
  • Memory for 5 charge / discharge programs.
  • Socket for temperature sensor
  • Two-line backlit LCD display with simple and clear menu and display parameters during charging / discharging
  • The safe operation contributes a series of text messages alert - incorrect input voltage, bad wiring, inadequate or battery status, incorrect polarity on output
  • Protection against reverse polarity and short circuit. < / Li>
  • Compact plastic housing, small dimensions
  • Built-in fan forced cooling.
  • Built-in power supply.


When charging a lithium set connect with service connector, you have the option to charge or discharge and monitor individual cell voltages and built balancer balances individual cells.

For temperature measurement of charging / vybíjených batteries can purchase a temperature sensor.

Note .: charger in the current firmware version (V1.0H) charging lead-acid batteries used end voltage of 2.40 V / cell - for this reason it is suitable for charging conventional lead-acid batteries (car batteries) and gel batteries with a reversible valve. Charging for gas-tight gel batteries, which must not be charged more than 2.30 V / cell, does not fit.



Charger kit includes: charger Multicharger X1 AC Plus, Ethernet cable, power cord with alligator clips 12 V adapter for service connectors lithium packs (2-6s) system ThunderPower after 1 pc charging cable with connector MPX 6 and Rx JR / Futaba, instructions .

Input voltage (car battery - DC) [V] 11-18
Input voltage (AC - AC) [In] 100-240
Charging current [A] 0.1 - 6
Discharge current [A] 0.1 - 1
Number of channels 1
NiCd [Art.] 1-15
NiMH [Art.] 1-15
Li-Pol [Art.] 1-6
Li-Ion [Art.] 1-6
Li-Fe [Art.] 1-6
Pb [Art.] 1-10
Balancer Yes
Output during charging [W] 50
Performance during discharging [W] 5
Balancer current [mA] 300
length [ mm] 112
Width [mm] 135
Height [mm] 61
Weight [g] 433

Doporučené příslušenství