Losi Desert Buggy XL-E 2.0 1: 5 4WD RTR Losi

Active Vehicle Control (AVC) technology

AVC technology is an advanced Spectrum technology from Horizon Hobby, for RC car models. This stabilization system brings a completely new way of driving RC cars. AVC technology uses sensors for steering and throttle corrections. Thanks to appropriate interventions in the steering and engine power, the result is a smoother ride, stable behavior on level ground and in corners and safer tracking. Of course, the variable sensitivity of the steering, including the possibility of turning it off and leaving everything in the hands of the rider.

AC regulator SPEKTRUM ™ COMPANY ™ 160A SMART

The model is controlled by a modern SPEKTRUM ™ FIRMA ™ 160A SMART controller with a 32-bit ARM Cortex M4 microcontroller, which is able to sense complete telemetry and transmit it to the receiver using an integrated wire in the new IC5 connector. Data is transmitted via the SRXL2 protocol. The controller reads information about the type, temperature and voltage of the battery cells directly from the Smart battery. You do not have to worry about the correct setting of the battery type and its possible undercharging.

The electronics are completely encapsulated in a special potting compound, which prevents the entry of moisture * or dirt into the electronics. The controller is switched on and set with the buttons under the rubber cover.

• The controller contains a fast and powerful 32-bit ARM M4 processor
• The regulator is waterproof *
• Overcurrent protection, thermal protection, failsafe
• Automatic disconnection of LiPol at low voltage
• Robust plastic housing, aluminum heatsink with fan for high efficiency
• Powerful BEC
• Highly durable IC konektory connectors, compatible with EC ™ connectors

AC motor Spectrum ™ Firma® 4P 780Kv

The car is equipped with an AC motor Spektrum ™ Firma® 4P 780Kv, compatible with 8S LiPol with which it can reach a speed of up to 80km / h!

Servo control Spectrum S906

Digital servo S900S with metal gears has two bearings, metal gears, speed 0.21 s / 60 °, torque 30 kg.cm, waterproof construction.

New central chassis reinforcement

Chassis struts are installed to reinforce the chassis, which are bolted to the central part of the chassis and reach up to the front and rear differentials.

Fuses on the screws

There are locking springs in the grooves against accidental falling out of the studs, which secure the half-axle drive sleeves on the shaft. / p>

Differential gearboxes

The new differential gearboxes have higher strength and ensure the stability of the drive train for a quieter, more reliable and trouble-free drive.

Reinforced differential holders

The new differential box holders have higher strength and ensure greater rigidity of the differentials on the chassis.

Aluminum differential body

The new aluminum differential body has higher strength and provides greater torsional rigidity than conventional plastic. Today's AC motors produce so much energy that it is necessary to choose materials with sufficient strength.

New shock absorbers with caps with the FOX logo

The new aluminum oil dampers have lower aluminum caps that make it easier to service and replace damper seals and improve performance. The top caps have a laser etched FOX logo for an inspiring look.

MAXXIS Creepy Crawler tires with Bead Lock rings

Original tires MAXXIS Creepy Crawler tires, with a universal tread for increased traction, give the car, like the original, great driving characteristics for off-road driving.

Aluminum shock absorber towers

In addition to the new shock absorbers, the DBXL-E 2.0 has new front and rear aluminum shock absorber towers with multiple mounting locations for better stability and maneuverability.

Drive system for demanding conditions

All drive components are made of steel and blackened against corrosion. The drive shafts now have a larger pin diameter of 5 mm.

Arrangement of electronics on the chassis

The chassis is made of high-strength anodized aluminum 6061-T6 with a thickness of 4 mm, on which are installed all important components, such as axles with differentials, engine, regulator, center differentials with differential wiring. The control is taken care of by a huge giant servo with a torque of 30 kg.cm.

New controller holder

In order to create more space for the batteries, the controller was moved to the mounting plate outside the center differential. This allowed for optimal weight distribution in the car while increasing the cooling efficiency of the controller.

New body look LOS05020V2T1

The color of the car is inspired by the real Fox Shox Motorsport racing in black-white-orange color.

New body look LOS05020V2T2

Finished colors typical for bodies in red and white with the Losi logo and flame.

Waterproof electronics

The RCXL-E 2.0 RC model is equipped with waterproof * electronics, including a receiver, servo and controller. The model is designed to minimize the risk of water entering the electronics, but it is necessary to minimize the risk of moisture, especially with regard to the motor, which does not have this protection and is therefore subject to the necessary regular service of rotating components, especially bearings. / p>

Lighting bar

The car is equipped with an LED light bar above the window, which can be switched on and off at will. So you can go night driving without worrying about getting lost or getting lost.

RC transmitter Spectrum DX3 2.4GHz DSMR

The new RC transmitter Spektrum DX3 has 3 channels and is compatible with the Spektrum AVC stabilization system and Spektrum Smart telemetry. Excellent range, super fast response and high resistance to interference thanks to the exclusive Spektrum DSMR technology. Quick setting of required parameters.

• LED indication of the state of charge of the Smart batteries in the model
• Support of the Spektrum AVC stabilization system
• Possibility of setting the reverse, the size of the deviations and the function of the 3rd channel
• Trim gas channel and control
• Thanks to the throttle limiter, you can limit the maximum speed of the model for children
• Ergonomic, lightweight
• Steering wheel with foam rim for a comfortable grip

SMART Spectrum Technology

The model is equipped with components with Spektrum Smart technology, which offers more information about the model, easier operation and battery care. All SMART components, including batteries, are able to communicate and transmit telemetry.

The included DX3 transmitter shows the charge status of the Smart battery in the model.

As tuning you can display complete telemetry ( speed, speed, temperature and more ):

• By adding a BT module to the DX3 set transmitter, which will enable the connection of the model with a clear graphic application Spektrum Dashboard in the phone or tablet.
• Using a universal Spektrum transmitter with a display, eg DX5C. <

You can find more information about Smart technology in our blog .

Recommended batteries

Operate the model on two identical 3S LiPo (11.1 V) or 4S LiPo (14.8V) batteries.

• For normal riding LiPo batteries Spectrum 11.1 V 5000 mAh with Smart technology
• For normal driving with longer operating time LiPo batteries Black Magic 11.1 V 6500 mAh.
• For maximum speed LiPo batteries Spectrum 14.8 V 5000 mAh with Smart technology.
• For maximum performance and speed LiPo batteries Spectrum 14.8 V 5000 mAh with Smart technology.

Spektrum batteries with Smart technology are currently the most modern and safest way to maintain and charge batteries. You can find the advantages of Spektrum Smart technology here.

Recommended chargers for conventional and Smart batteries

• Mains charger Spektrum S2100 with two outputs 2x 100 W
• Mains charger Spektrum S1100 with one output 1x 100 W

To connect the battery to the above-mentioned chargers, you need an IC5 / IC3 charging adapter.

• High-performance mains charger Spektrum Smart G2 charger S1400 1x400W AC with one 400W output.
• High-performance mains charger Spektrum Smart G2 charger S2200 2x200W AC with two 2x200W outputs.

Protective covers for batteries

Protective covers are designed to reduce the risk associated with transporting and charging batteries. LiPo batteries can, while maintaining small dimensions and low weight, provide high discharge currents and have a large capacity. The LiPo battery is prone to mechanical damage and therefore needs to be thoroughly protected.

Accessories for normal operation

For normal operation of Losi RC cars, you need glue for screws, quality glue for tires, silicone oil for shock absorbers and a set of screwdrivers. From our range we recommend an affordable set of tools for cars or a quality set of Allen screwdrivers 1.5 / 2.0 / 2.5 / 3.0mm. We recommend that you look at the Tool Sets

The screw glue drips the thread or the head of the screw, which fixes it and the vibrations caused by driving do not allow the screw connection to loosen. The screw adhesive has a special composition that allows the screw connection to be easily loosened with a reasonable torque without damaging the screw head. Never use ordinary instant glue, it could be impossible to loosen a screw glued in this way at all!

The tire glue adheres the tires to the rim of the disc. It is always necessary for the tire to be firmly glued to the wheel rim around the entire circumference! If the tire is not stuck around the entire circumference, it may rupture. The tire adhesive has a special composition that is able to bond materials such as rubber or nylon, and at the same time, after hardening, the adhesive is flexible. Never use ordinary instant glue - it is not flexible after hardening and cracks in the tire would gradually form around the rims!

Occasionally it is necessary to add silicone oil to the model's shock absorbers. During normal operation, there is only a slight leakage of silicone oil along the shock absorber piston rods. If the surface of the shock absorber piston rods or the condition of the seals is in poor condition, the oil leakage can be large. For these cases, so-called repair kits are supplied. In the range of tuning parts, piston rods with an extremely hard TiN (titanium nitride) coating are supplied with all shock absorbers. You can easily recognize the piston rods with a TiN surface by the gold-green color.